adjustment

I recently noticed that the clutch pedal had to be pushed all the way to the floor to shift into 1st and felt stiff, especially if cold. 2006 RSX-S that had aftermarket CMS and Slave about 2 years ago because of a leak. No leaks now and the fluid level is stable. The free-play was about 22mm...

I find that these are really the only tools you need to do the valve adjustment on the 02 Type-S. Its not terribly difficult. I'll expand more if there are any questions. Paul

After installing the A Spec sport suspension, did anyone find it necessary to realign their headlights (and fog lights)? Thanks for responding.

So I got the stance pro comp coilovers for my 06 type s and I've seen a decent amount of posts on how to adjust the back cause the way you have to do it is retarded so i figured I'd post the email they sent me on how to do the front and back. But other than adjusting them being a little...

I took my lowered 2003 base model RSX into Firestone to get an alignment done because my rear tires are pigeon toed and wearing really fast, they told me to install a camber kit because the camber and toe is maxed out and straightening the camber will change the toe so I installed the camber kit...

Hey I'm new here and was curious if anybody has info on using k pro at high altitude. I live in denver and have a CAI,RH, and exhaust. Just purchased k pro and wondering if their base maps are any good seeing I live a mile above sea level. Any help would be appreciated.:love:

I can't find any diy for the 05-06 type s models. Did something change those years to not require valve adjustments?

Hey everyone, I bought my car used a couple years ago from a guy that had installed tein ss coilovers on the car. I love the way the car looks when its lowered like this but I have been getting frustrated with the constant scraping of my midpipe and exhaust over the years. I read on here that...

Hey guys, its almost time for the scheduled valve adjustment on my 2006 type s and im wondering if i should get them to check anything else while its in there, ie. Timing chain, cam bearing clearances, cam lobe wear?

What's up crsx! So recently my friend bought an RSX (108k miles) and has low compression in Cylinder 2. Here are the PSI Readings. This test was performed with engine already warmed up, ecu disabled, and throttle fully depressed when cranking the engine 3-5 times. Cylinder 1: 180ish Cylinder...

hey guys I have been running D2 coilovers on my ep3 for the past few months, they ride pretty good, there the 1st gen D2 coilovers. spring rates: 8k F 10k R so yesterday I did my oil change and decided to lower my front coilovers 1 inch more. as I was lowering the collars I noticed the spring...

Sup guys. Can ya'll take a listen to my motor and listen to if it needs a valve lash adjustment? I feel like it does but a second opinion always helps :weeeeeeeeee: https://www.youtube.com/watch?v=Ok4FLIwurh4&feature=youtu.be

I just lowered my ride 2 inches with stock 03 wheels. When I go to get my alignment done will they adjust my camber too I installed a front and rear camber kit. Also how do you know how much camber to put.

Hey everyone. I was experiencing very bad ticking and loss of power, and found that my cams were galling on both exhaust and intake side. I don't have funds for Kpro, so I just bought Stage 1 Skunk 2 cams. Installed them and they are perfectly in time and everything, I just have a quick question...

Nvm

Hi, I recently got a 05 rsx-s and the clutch was just replaced. It grabs good and it doesn't slip, but the engagement point is literally at the top. I want to lower it a little bit because I'm not used to clutch engaging this high. I did my research on the forums and found...

In my case I bought the Alpine RUX-KNOB off of ebay for roughly $20 and i wanted to install it in a place where it'll still keep my car looking clean and can be hidden. Sorry for the huge pictures! Difficulty: 2 Tools Needed: Long Philips head screw driver Drill/Drill Press 1/2in Drill Bit...

i bought my car with 170k miles and im wondering what are the symptoms if i need a vale adjustment thanks!

Hi just testing the waters on my coilovers. Has dampening aswell. They are still on the car they ride great but im looking to go lower, these go for $1200 + new and have camber adjustment aswell. Coils have about 2500km on them so they are pretty new still. Never used during winter as the car...

What should I just the valve lash to when doing a valve adjustment with Blueprint Stage 2+ cams? Done my research, Blueprint has been out of business. No one to call, no discussions about these cams. Not sure if the factory clearances are suitable.