Acura RSX, ILX and Honda EP3 Forum banner
bent
1-19 of 151 Results
Advanced
  1. Problems & Solutions RSX
    ..
  2. Problems & Solutions RSX
    After running fine i went to leave, it would crank about 20 seconds and go dead. Kept doing that for a while, had someone come look at it, started it up, it stayed going but sounded like crap. Sounded like it wasn't getting enough gas, spitting and sputtering so I cut it right back off. After...
  3. Suspension, Chassis & Brakes
    So i was driving in some seriously heavy snow, and messy roads. I came over a hill nd long story short, I slid at about 30 mph straight into a sharp 4 inch curb. The car got towed home, and the subframe is bent badly on the passenger side, among a broken wheel and collapsed control arm and other...
  4. Suspension, Chassis & Brakes
    So I brought my car the the mechanic to get it balanced cause my wheel shakes at high speeds. While doing an alignment check one of the guys noticed that my front right shock is bent and leaking. He told me I should get new shocks and Springs. I was reading reviews on the koni yellows and...
  5. Problems & Solutions RSX
    Like the title says, my RSX has pulled to the right since I bought it (used). I took it in for an alignment and they said that they did all that they could for the alignment but the pull was caused by a bent front right control arm as well as a slightly bent frame. I found what looks to be the...
  6. Transmission & Drive Train RSX
    Just installed my Buddy Club short shifter, something loose and bent? [PICS & VIDEO] Hey everyone. So I just got done installing my new buddy club short shifter on my 05 type S. With 140K miles, the stock shifter was very sloppy and made a clacking sound. The install of the buddy club went...
  7. Engine & Transmission RSX
    Hello i have a brand new never used 3 in thermal mandrel bend exhaust for rsx i paid 620 for it askin 400 im im ny willing to meet up call 3475209636 i will text pics
  8. Transmission & Drive Train RSX
    Alright guys so I had a horrible misshift going into 1st gear and bent the hell of out my 1st gear fork. How hard is it to replace a shifter fork? Would I be better off getting an entirely new 6 speed transmission? Trying to decide which option would be cheaper at this point. Thanks! :fistbump:
  9. Problems & Solutions RSX
    Alright so my 2006 has an issue with pulling left at moderate to high speeds. The car/steering wheel does not vibrate at all so I assume the wheel is not bent (or at least heavily) but there IS a slight air leak on my driver side front tire that I occasionally have to fill back up to 35 psi...
  10. Southern California For Sale: Local Pick-Up
    Piping is 3" mandrel bent with resonator to a 3" vibrant stealth muffler Has scrapes from previous owner on midpipe Looking for q300,hks hi power, etc. located in irvine You can reach me at 9492593870 Can take better pictures upon request
  11. Suspension, Chassis & Brakes
    i have a-spec suspension in my base auto rsx. so houston construction has gotten pretty bad, and i hit something in a construction zone. fixed up everything, but there's a bent strut/caster and i doubt it can be bent back. someone suggested i buy a stock strut and put the a-spec shock and spring...
  12. Problems & Solutions RSX
    2005 RSX S Head Replaced (50 miles ago) used head 120K from good running RSX. Loud ticking Started and ran fine, then started missing on Cyl 1. Checked Spark - OK Spark plug installed - Car running fine Drove 20 miles no issues except idle not correct During drive car would sometimes idle and...
  13. Problems & Solutions RSX
    Hello to all and welcome to my mini nightmare. I got my 2006 base Rsx about 2 months ago 5 speed 152,000 miles Car was owned by an older lady who had it serviced at a ford dealer ( yea go figure ) always. Mainly driven on the highway for almost all it's life. Since getting it I have...
  14. Texas For Sale: Local Pick-Up
    ..
  15. Problems & Solutions RSX
    So I just had a noob moment and jacked car up using rad support....I know, stupid. So now it's bent and hood won't shut properly. What do I do now:(
  16. Problems & Solutions RSX
    I need help guys.. I don't know what to think or do.. So here is the story. I have a 03 type-s (130k miles) and 2 weeks ago I was cruising in my car and it all of a sudden started bogging down bad like the car was running super lean. I had to brought to a mechanic and the cause for the problem...
  17. Problems & Solutions EP3
    So i hit a curb the other day going about 30mph, since i my ep is lowered and i have crappy tires it kinda skitted and i hit the front corner of the subframe on the Driver side which bent the frame itself which is kinda bad (just the corner) and they also told me i bent the control arm. So now...
  18. The DIY Garage RSX
    so,,been searching around, seems like lots of you are having this problem but no one have written a solution, hope this helps first of all i didn't do this, some random guy at the tire shop jacked my rad support and it bent:bsflag: hood won't close properly tools you will need : jack jack...
  19. Southern California For Sale: Local Pick-Up
    FS: is 3 Advan Rg1 rims in gold with falken ziex 512 at 70% tread, one of the Advan rims got bent and is with sale im not sure if it can be fixed but for what its worth its sold all together. rims are 17x7.5 +35 , located in Vista, CA 92081, pickup only price is $750 obo...
1-19 of 151 Results
Top