Acura RSX, ILX and Honda EP3 Forum banner

changing

  1. P0134 but A/F is changing in KManager

    Problems & Solutions RSX
    So I installed a KPro V4 in my RSX a few days ago and the code for P0134 popped up in my KManager program only after the ECU was installed. While performing a datalog though I noticed that the car was not in limp mode as I've noticed others say happens and I'm able to see the AFR approach 14.7...
  2. Changing 94 N/A octane map to 91. What to do?

    ECU Tuning RSX
    Hi guys, haven't touched my kpro in YEARS. I've driven on 94 oct for last 7 years but now gas is getting to be a little too expensive in my area. Im wanting to back down to 91, what should I change in my map? my mods are I/H/E/intake manifold. Im thinking stepping down ignition slightly across...
  3. Changing your cabin filter - video attached

    Car Care RSX
    If you want a walk through to changing your cabin filter for fresh interior air... or your really bored and want something to watch... Click Link Below Click here ----->> https://youtu.be/MXnRyCXLiVw
  4. Changing color for my rsx

    Exterior Mods RSX
    I have a 06 blaze orange rsx and I want to change the color. I would like your in put to which 3 colors to pick. I'm thinking Jade green, pearl white or any type of gray :)
  5. Changing front struts (clunking) What else should I do while in there?

    Problems & Solutions RSX
    I have an 02 base rsx and it has about 130k, I have had some clunking over bumps which has gotten more severe over the past 5k miles. I have it narrowed down to the struts. I am going to be renting a spring compressor and installing new struts. All of the front end components are factory as...
  6. Changing Headers On a Auto?

    Bolt-On Basics: RSX (Base)
    So I drive a automatic RSX BASE model (2003), and I was wondering if it was a dumb idea to change the headers on it. Some people say its a "dumb idea" because my car is an auto but I want to know what you guys think?
  7. changing the tensioner pulley

    Problems & Solutions RSX
    Long story short i was changing the serpentine belt because it was cracked and i was doing the tensioner pulley as well and once i got the belt off i loosened up the bolt on the tensioner to remove the pulley and when i got it out the retaining nut in the back fell of never to be seen again...
  8. Compressing piston when changing pads

    Suspension, Chassis & Brakes
    When changing brake pads on the RSX is it required or recommended to open the bleeder when compressing the piston. I hear that it can damage master cylinder or the ABS unit in some cars if you don't. But I am not sure if that applies to Hondas. The service manual makes no mention of opening...
  9. Changing springs by only taking off top hat or caster plate?

    Suspension & Brakes EP3
    This would be so nice. Is there room somewhere up there to slide spring off without messing with the bottom attachments? - Hotchkis plates (no top hats) - Koni/GNC/remove 8" 336 lb. spring - install 7" 400 or 450 lb. spring, I think, haven't figured out spring length yet
  10. My Car Idle at 2500 rpm after changing the TB

    Problems & Solutions RSX
    I change the Throttle body on my 2005 RSX type S and my car start to idle at 2500 RPM the reason I changed the throttle body is because my TPS broke can someone help me out
  11. srs light on after changing seats

    Problems & Solutions RSX
    So my seats were completely torn up in my 02 type s so I bought some oem nice ones off a 2006. After installing them, the srs light stays on. Any idea what the problem is? I double checked and everything is hooked up Thanks a lot for your help.
  12. problem with changing gears

    Problems & Solutions RSX
    My shift feels like my gear might be sticking 5th gear is really hard to shift out of I have to pull on the shifter knob hard.also 3rd is tough. Any ideas what it might be? Maybe I need a new clutch or new fluid? This happened out of no where it was cool in the morning and when I drove in the...
  13. steeing angle and toe changing on hard turns

    Suspension, Chassis & Brakes
    lately when I drive my car hard when autocrossing my alignment gets screwed up. Also my steering angle changes a little, but when I make a hard turn the other way it like goes back to where it originally was. I have the skunk 2 pro c coils and I was thinking that the lock nut on the bottom part...
  14. changing front and rear rotors and brakes

    General RSX Discussion
    i m going to change my rear and front rotors and brake pads today!!!! wish me luck!!!:)
  15. 06 RSX S VBP A-Spec *Work, ARC, Cusco, Bride* UPDATED 5/25 (First Post)

    Member Show-Off RSX
    follow on IG: halteman97 Well I had a 2002 RSX base in NHBP, and got a really good deal on this 06 VBP my friend couldn't afford anymore. The 06 VBP was basically my dream RSX (obviously other then a true Type R). This car was built for form>function so if you don't like it then feel free to...
  16. Changing ECU

    ECU Tuning RSX
    Hello Guys. I`m the owner Honda Accord 05 5MT with very similar to yours K20A3 engine - K20A6 ( European version). I changed intake manifold on RBC, and now I have a problem with P0401 error. In my engine I have EGR valve. I would like to turn off, but this is a problem. To fix the problem, I...
  17. Whine when accelerating in low gear after changing clutch fluid?

    Problems & Solutions RSX
    Hi! I tried searching the forum but couldn't find anything addressing the issue I'm having with my 06 Type-S, so I'm hoping someone might be able to give me some ideas on what could be causing it. And I apologize in advance if I use the wrong terms or otherwise sound like an idiot--I adore my...
  18. changing out the clutch

    Problems & Solutions RSX
    i'm changing the clutch in my 06 base model rsx and my release bearing is stuck on the tranny shaft is there a good way to get it off ???? and when going to remove the bots on the pressure plate the fly wheel just pins good way to hold it in place anyone ?? :lostswimmer:
  19. A couple issues while changing starter

    Problems & Solutions RSX
    Ok. First and foremost thank you in advance for any advice/help. So i've decided to change my starter myself(2005 base). And i decided to use the method of removing the intake manifold & i ran into a couple issues. Using the correct size socket(12mm) and it slipped, semi striping one of the...
  20. annoying sound when changing gear

    Problems & Solutions RSX
    Wassup people! I've been getting this weird sound as of lately, and it seems to be coming from under the car when i change gear -as i'm letting go of clutch and adding the gas pedal. Sounds a bit like when you move heavy wooden furniture thats been there for some time, and it kind of...
Top