Acura RSX, ILX and Honda EP3 Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-17 of 28 Results
  1. Bolt-On Basics: RSX Type-S
    Fortunately for us, cam selection sucks. The Honda K Series community suffers from the luxury of abundance. This worksheet is an attempt to comprehensively collect all available options for the K Series and an approximately standard method of comparison.I was forced to take some liberties and...
  2. Wheels & Tires
    Was wondering if this could be make a sticky. Could help out alot of the guys who mess around with tire sizes, those who want to fill well gap, guys who wonder if certain set-ups will fit, etc. 16 inch tires - tire/height 205 40 16 - 22.46  215 40 16 - 22.77  225 40 16 - 23.09  195 45 46 -...
  3. Engine Building & Design
    I've been searching all over and can't seem to find anything on it? Anyone know the different sizes per color? Trying to order some bearings for my Manley rods. I have the size of rod and crank journals but just need a bearing size chart... Thanks for any help or info..
  4. All Motor RSX
    The blue line is my k20/k24 87.5mm 12.5:1 pistons, blueprint stage 2 cams (old version), buddy club race header, 70mm throttle body, rrc intake manifold, custom 3" exhaust, tuned on kpro 91octane The red line is the same as above but with a mugen twin loop exhuast which is 60mm or 2.36" The...
  5. Bolt-On Basics: RSX Type-S
    Ok well I decided to post up my dyno chart for my mods, just in case it might help someone later down the road. Car and Mod Information 2006 RSX Type S, 70k miles I made four sets of dyno runs (three each). 1-3. Stock, no mods whatsoever 4-6. Added Random Technology High Flow Cat, DC Sports...
  6. General Discussion EP3
    http://www.35pickup.com/mulligan/weight.txt I know its not honda but I thought it was interesting....:pimp
  7. ECU Tuning RSX
    Hey guys, Firstly modifications, RBC inlet Hondata Inlet manifold gasket Kidd racing header 2.5" system and backbox K-pro ECU - Running RSX cold air map. PLEASE TAKE NO NOTICE OF THE HP ON THE DYNO AS IT WAS DONE FOR A/F SO NO RUNDOWN FOR LOSSES WAS DONE. It made 192 BHP ATW I put it on...
  8. All Motor RSX
    K20 head, K24 block Bisimoto spec Arias Shelf Piston Eagle Rods Bisimoto Level 3 valvetrain Custom Intake Manifold Custom 4-1 Header Stock Type R 6-speed Tranny 75mm TB K-Pro Pump Gas 274.70whp; 206.85ft/lbs
  9. Turbo RSX
    THIS IS THE CAR IS GOING ON TURBO KIT sidewinder t4 turbo manifold precision sc62 with billet wheel ported s housing .70 compressor and .58 turbine 3" downpipe dumptube 44mm tial wg 50mm tial bov aluminum ic piping 4 ply couplers t bolt clamps oil feed oil return lines same side...
  10. Exterior Mods RSX
    i remember seeing a chart of some sort comparing different exhaust sound, fitting and performance? i cant seem to find it.. HELP?
  11. 1/4 Drag Racing RSX
    First of all, thanks to K20A2 for the formulas to do this. I have been trying to decide on what wheels and tires to use for drag racing this season. I have pretty much settled on Team Dynamics Pro Race 15x7 rims and BFG 205/50/15 drag radials. I was working on this chart and thought others...
  12. 1/4 Drag Racing RSX
    I was looking at the altitude conversion chart and read that the correction for 2600 ft was .9692... I ran 14.75 @ 95.5 MPH...without the correction. with the correction i ran a 13.78 @ 96.53 mph..unless i did it wrong.. all i have done to my car is a DCRH, SRI, axleback ( does nothing) that...
  13. 1/4 Drag Racing RSX
    I was looking at the altitude conversion chart and read that the correction for 2600 ft was .9692... I ran 14.75 @ 95.5 MPH...without the correction. with the correction i ran a 13.78 @ 96.53 mph..unless i did it wrong.. all i have done to my car is a DCRH, SRI, axleback ( does nothing) that...
  14. 1/4 Drag Racing RSX
    I was looking at the altitude conversion chart and read that the correction for 2600 ft was .9692... I ran 14.75 @ 95.5 MPH...without the correction. with the correction i ran a 13.78 @ 96.53 mph..unless i did it wrong.. all i have done to my car is a DCRH, SRI, axleback ( does nothing) that...
  15. Turbo RSX
    Anybody have a bearing sizing chart for the K20A2. Something like this: This is a Earl Laskey's chart for a B series Main Bearing thickness by color Blue 2.013-2.010 mm 0.0793”- 0.0791” Black 2.010-2.007 mm 0.0791”- 0.0790” Brown 2.007-2.004 mm 0.0790”- 0.0789” Green 2.004-2.001 mm...
  16. Suspension, Chassis & Brakes
    Thought maybe we should make a list of all aftermarket springs and coilovers made for the RSX, their drop and their spring rates, just like how evom.net did: http://forums.evolutionm.net/showthread.php?t=66296 I'm just listing as many springs/coilovers I can think of for now, if you know their...
1-17 of 28 Results
Top