Search Results for ‘cylinders’

I am not getting any Compression in any of my cylinders. I have checked for water in my oil and there isnt any. There isn't any oil in my water either. The compression test shows 0 at all cylinders.

Bought a 2002 type s 5 months ago and just love it. Has some bolt ons and eventually going to do a build. Love the input on these forms.

Driving to work on a very cold winter day in february, my type-s started missing pretty bad out of nowhere. The check engine light was flashing so I did a diagnostics to find codes for misfiring on all cylinders. I changed the spark plugs, coils and checked the fuel pressure. Everything...

I have a stock 03 EP3 which has two cylinder (outside two) not getting a pulse to the injectors. I have checked all coils and plugs and all are firing correctly. I have swapped injectors and they will work fine on the two cylinders that are getting the pulse. Hooked the noid light up to the...

So I just picked up this 02 type s and it has a check engine light. Plugged in the code reader and came up with misfire and all four cylinders and bad o2 sensor. I replaced the first 02 sensor and new plugs iridium but still idling rough. Engines shaking. The car has headers intake and test...

Thinking of converting your car to a dual master cylinder set up? You'll find this new dual mc torque and brake bias calculator tool to be what you want in helping design that new system. Complete with all the things you need to set your parameters it also allows you to "dial in" the bias with...

So I was driving the other day, went to turn around in a circle and my car shut off. I tried to start it again and it wouldn't. When I did a compression test I was not getting any reading out of the cylinders. I'm not sure if maybe the car jumped time and I should replace the timing chain or if...

So here is the problem I removed my intake, rbc, and rdx injectors, I then installed precision 650 injectors ( I soldered in the harnesses) to accommodate my new mag e85 tune. So now when I start the car only the 2 cylinders on the passenger side are getting fuel or firing I tried putting the...

Just want other peoples input on this. So i changed my slave and master cylinder because it was leaking, but prior to that i had no problems with shifting or my clutch slipping. Right when i got my car back from the shop the clutch pedal wasnt as stiff as it was before and shifting into 1st and...

I just wanted your alls opinions on this. I have a newly built motor that has been put in my EP3 with JE pistons 9.0:1 compression. I have my car at the tuner and he decided to do a compression test on the motor before tuning it WOT. He pulled the numbers as follows: 160 180 160 185 Is this safe...

Brand new Civic Clutch Master cylinder. Great upgrade for people running stage 2 and up clutch kits on their rsx. $55 shipped SOLD Used and perfectly working Clutch slave cylinder $35 shipped SOLD k20a3 knock sensor with pigtail $35 shipped SOLD 3 inch high quality resonator that is used but...

So I myself am not a car guy, so I am not as aware of how everything under the hood works. So here I am again asking the internet for some direction. :dontknow: I drive an 02 Base 5-speed. dont race ^^cause of that lol No engine mods either. 121xxx miles treated like a baby But my...

I've bought a 02 type S with the impression of bent valves on one cylinder. But now I am not so sure because I'd just done the compression test and one cylinder is 120 dry, 135 wet with a cap of oil added, while other cylinders have 200-210 ish. So then I did a leak down test. The gauge says...

Alright so I got the rsx (base auto :( ) in september, it had 56k on it. The first thing I did was checked the spark plugs and filters and everything, I changed the filter, but the plugs looked fine. Now I have been getting around 17mpg...so I decided I needed to check the plugs and coils...

Ok I did a frank swap in my rsx everything went right untill I tried to start it.. I have 120 compression in piston #1 and 0 compression in the rest of them. What went wrong during the build? Please help. I used a k24a1 block with a k20a2 head.

So here is the deal...I put in a Act ar1-hdss clutch kit along with the Act streetlite flywheel @ 61k. At that time I replaced the Slave & Master cylinders. At 66k master goes bad I replaced it now @ 70k the Slave is going bad. Any reason why this is happening or a recommendation on a company...

I hit fuel light on the way back to work from lunch. Pulled over, put in $10 of BP 93 gas. (Never gotten BP gas before.) Leave the gas station, car running fine, get to work a mile down the road and turn off the car. Twenty minutes later I get in the car to run an errand, and immediately as I...

Hi All, Need to see if someone could give me more insight on why my CEL stays on after reverting my car to stock from turbo. It seems to only occur after driving for a long period (+30 minutes) and then stopping at a signal at idle. The CEL only occurs during no throttle, or idle. There are...

I am looking for a couple of them so that I can cut them apart and see where they failed.

hey guys, just finished putting my motor back in. im getting no fuel at the injectors. i have fuel pressure at the fuel rail but injectors arent working except cyl#3. any ideas?