Search Results for ‘datalog’

Just started up my EP for the first time in a year (nearly to the day). I just installed a rebuilt K24A1 (block and head) with Arias 8.5:1 pistons and Eagle rods. Turbo set up is same as before on the K20A3, cooling is the same, as is the fuel system. I put diesel oil in it, 15w-40 to lube...

the past 3 days ive been having trouble with my car. out of nowhere, it wont start anymore. i have tried many things like a brand new map sensor, checking the wiring, adjusting valves, ensuring timing is correct, cleaning IACV and throttle body, replacing throttle body gasket, confirming...

Still trying to learn how to tune A/F, I think I have all the knocks out, is the car running too on rich or too lean, this is on the CAI KAL on kpro

My datalog gents. take a look and give me some suggestions or make some corrections lol if you dont mind. knock sensor is disabled. power mods are passwordjdm intake obxr v2 headers stock exhaust 10lb flywheel

at full throttle i can rev it up t0 8k and it will go fine but at partial trottle trying to hold it at 3k it wont hold there it just drops down and goes uo and drops down and goes up.

I've been having this problem for the past month or so now. 95% of the time I shift from 2nd to 3rd (half throttle to WOT...doesn't matter) my A/F spikes and hits lean cut. If it doesn't cut out it goes to 17.0:1 or so before it finally drops back down. If I granny shift it and accelerate slowly...

can anyone look at my datalog and tell me if its at least ok? am i running too lean or too rich? i have no idea how to tell.. i dont even know if its safe please can anyone help a brother out.. no kpro knowledge at all lol thanks

i have kpro im getting some issues for dataloggin when im runing in the car it shows the reading on my computer, but when saved the datalogs and run again to show all the logs i dont show AFR this is problem of WIRES, OR NORMAL? let kenow how to fix it. im final step for tune it, and join...

Well I finally did a datalog and found 2 knocks... Need help with reading the datalog and trying to learn more about tuning in the process.... I am going to upload the file... I have the basic bolt on's IHE... If there is anything else I need to post please let me know... Thanks....

Hey guys im pretty new to kpro. I have been messing around with different calibrations and am starting to get the hang of it. My concern is that im not getting any knock. I no it is good to have zero knock but not having any knock with the tune that i tried is making me believe my knock sensor...

just starting to learn how to use kpro here is my first datalog and i am using the k20a2 cold air dyno tune cal. I have aem cold air intake, crsx header, apexi ws2 exhaust. how does this look and what should i do to improve? thanks for the help

ok so i dataloged 3 pulls. one on 2nd gear, went fine. one on 3rd gear, went fine. this is where my problem starts. going from 2nd to 3rd i get cut off when in 3rd gear. and will not let me keep going. im assuming the lean protection. any help wld be greatly appreciated cuz apparently the tuners...

Trying to finish up my rebuild, only thing I have changed engine wise is a 70mm Skunk2 throttlebody. It barely starts up and run like its untuned with drag cartel cams, super rich, and when the throttle is pressed there is no feedback but a sluggish almost miss fire sound. Ive replaced/checked...

here i will post up my tune and my data long..... in this log i aint get much knock but in 5th gear high rpms it gets bad! please help if u can or take a look! thanks crsx, mike

so guys my friends and i finished installing the skunk2 intake manifold into my car so i turned it on and it starts fine but starts to accelerate on its own to 2500 then to 3000

So i just got kpro and loaded up a cal. I began recording a datalog for the way home but didn't see any graphs on the display. I thought it was normal and could only see it after loading it later but i load up the datalog and still doesn't show any graphs but does show the time of the recording...

Post ur .Kal and a .Kdl With some basic info about ur setup or problem ur having. Looking for quality info here lets keep it on topic and free of non relevant info. Everyone that posts needs to either submit a datalog or comment/critique on a tune though. It will be disclaimed that the thread...