Acura RSX, ILX and Honda EP3 Forum banner


  1. does anyone know how to help?! [ CAR DOOR ISSUE]

    The DIY Garage RSX
    So my brother and I decided to replace the driver door lock actuator on my Rsx today, and after following the featured thread recommended on here and much struggle after some tiny plastic piece on the door lock assy broke off, we got the new actuator in. At first all seemed well, we tried the...
  2. DIY: Replacing shocks and tie rod ends - KYB

    The DIY Garage RSX
    I replaced all 4 struts and the tie rod ends. I utilized KYB shocks and Moogs tie rod ends. Failed inspection because of that crap and the car needed a lil' bit of love anyway. You guys have see the steps to get the RSX safe and inspection ready. This is a simple and easy task that I personally...
  3. DIY: Replacing the AC compressor and mod ac lines

    The DIY Garage RSX
    What's up guys! I'm living at Maryland now and work close to DC. I didn't need ac in Germany but the traffic here sucks soooo ac it's a must! I didn't want to use the stock lines because I'm going sidewinder with a 6262. I also didn't want to use the EP3 lines. Some welding had to be done but I...
  4. DIY How to reset your SRS Light

    The DIY Garage RSX
    Figured this has been post many times, but the videos I found on youtube are quite long. So I went ahead and made this video, straight to the point and only 5 minutes long enjoy! :hb: :hb:
  5. R wing removal hole fill diy tips????

    Exterior Mods RSX
    So i searched the threads and couldnt find any involving wing removal techniques. What Im specifically looking for is somebody who has done the job with good results that could share some knowledge. Id like to fill the holes and touch up paint if possible saving the costs of painting the whole...
  6. Windshield wipers park in random positions!! - DIY

    The DIY Garage RSX
    What's up guys? Here another DIY on how to fix the issue with the wipers. I replace the motor, check continuity on the switch and check continuity and voltage on the fuse box and nothing fixed the issue. I took the fender out and BINGO! 3 wires were cut. Check the full video on the link below...
  7. Knock sensor removal DIY

    Problems & Solutions RSX
    I have been following the steps in the DIY post from CyborgGT on Nov 3, 2015 to remove the knock sensor. I have disconnected all electrical and hoses. I have removed the 3 10mm bolts on each end of the top brace and the 2 10mm bolts holding the AC line and the plastic snorkel to the air cleaner...
  8. HID kit DIY

    The DIY Garage RSX
    Hello guys! Another easy DIY and this time I'm replacing the old HID kit on my RSX. Thanks a lot for your support! Please subscribe!
  9. DIY: Kseries Transmission Rebuild

    The DIY Garage RSX Hopefully this helps with your trans rebuild
  10. Need a dependable mechanic for a DIY

    Canada East
    Hi guys Reaching out the community to see if there is anyone in the GTA who is skilled and has assembled some DIY time on their own RSX's. I'm looking to do a k20z1 w/lsd tranny swap with a new clutch, flywheel, rear main seal, new control arms , subframe collar kit I don't trust any shop at...
  11. Electric Power Steering (EPS) DIY for $10

    The DIY Garage RSX
    Hello again! I made a DIY of how to do the EPS conversion. I used an EP2 instead. The EP2 is the base model (European version) of the Civic Si we had in the States. I know this DIY it's been done by the guru @spaz :hb: long time ago but I just wanted to do my version. Enjoy!! PS: Please...
  12. Delete please

    The DIY Garage RSX
    Please delete admin
  13. Tony West DIY - New YouTube Channel

    The DIY Garage RSX
    Hello guys! I started a YT channel and I'll be posting different DIYs for the RX-7 FD and the RSX. In addition of cars shows and more! I hope you guys like it! :fistbump:
  14. DIY: Inner Tie Rod Removal / K-Tuned Upgrade

    The DIY Garage RSX
    Decided to install some ktuned inner tie rods to correct toe issues I was having with being lowered. The ktuned are adjustable inner tie rods meaning you can adjust the length to either bring your toe in or push it out getting your tires straight. It is a common problem for people who lower...
  15. DIY: DC5 Recaro Bolster Refinishing

    Interior Mods RSX
    Now there is a good DIY for disassembly and whatnot available there’s no point to remake the wheel so to say... DC5 Removal/Disassembly This DIY is aimed more at a good reputable company to purchase the replacement bolster foam and suede covers. All links listed below were the...
  16. DIY SUPERWRAP gloss black wheel spray

    The DIY Garage RSX Today I restored my beat up old OEM 16 inch rims with SUPERWRAP VINYL WHEEL SPRAY. It’s an affordable way to add new life into your wheel setup without the price of powdercoating. THE BEFORE, STOCK 16 INCH OEM RIMS BALLER OEM...
  17. DIY caliper rotor brake pads and stainless steel lines

    The DIY Garage RSX
    we did a reverse DIY on how to replace brake calipers, rotora, brake pads and stainless steel lines. we hopes this helps you guys and if you have any questions please feel free to ask here is a link to the DIY
  18. DIY morimoto h1 projector retrofit!

    The DIY Garage RSX
    the process was a lot easier than i imagined. i included a video of the process
  19. DIY: Power Mirror Light

    The DIY Garage RSX
    First post- I searched but couldn't find anything similar, hopefully it can help someone else out Just bought an 06 Honda Integra here in Australia for my daughter. I was perplexed at all the buttons etc that didn't light up at night. After searching around and pulling lots of things apart I...
  20. DIY Custom Ground Wire System

    The DIY Garage RSX
    I started making my own ground wire system for my 2002 RSX Type S K20a2. To clear the air about these aftermarket grounding unit, the actually do make the engine run smoother, help out with gas mileage, and possibly make a couple extra HP. Taking sandpaper and removing the paint where chassis...