Rique_souls: What’s up guys I’m new to the car community so please help me out. I wanted to refresh and modify my RSX 06 base automatic (I know we all prefer manual). The engine has 201k miles on it but it hasn’t given me any real problems no check engine light or anything but the engine bay and...
On the base rsx the throttle position sensor is on the opposite side of the type s. U need to depin and switch over the corner wires. The middle stays the same. Would bog out under wot. Check tos calibration to be sure u got it right
Any good performance shops for Honda/Acura located in or around Austin Texas?
I have an 03 RSX type-S.
Thinking of going with bigger turbo setup need more power!! Also, want to install some upgrades internally too!
Please post all recommendations!
Thanks in advance ?
I have a 2002 Acura RSX Type S K20A2. It has a JRSC race edition still the original blower pulley, PS & AC delete as well.. My engine randomly started making a grinding noise to where it sounds like a dang chainsaw. You don’t hear it while at idle but once it gets above idle RPMs you can hear it...
So my check engine light was on for a while and i finally decided to get it read and it was P0304 (Missfire No. 4) and the primary O2. I did all new plugs and coils and new O2 and the light stayed off for about a week until i raced some guy then the light was back on when i started my car later...
Hey guys, so I made a pretty dumb mistake when ordering my engine harness from WireWorx 2 years ago. I have an 02 RSX and ever since I ordered the harness, my speedometer has not worked. I couldn't figure it out for the longest time. Well yesterday I figured it out. When ordering my wireworx...
Hey all here in Cali just got state refereed for smog (fucking sucks ass) so now I'm forced to pass and basically putting the car back to 100% stock. New here so a quick rundown I have an 04 Type S with OEM K20a2/transmission. Bought the car off my brother 2 years ago and just replaced the full...
help me sort it out please
supertech valves ,
3 angle valve job
ported and polished head
arp head studs,
je jd pistons 9:1, hd wrist pins, 87mm
manley turbo tuff rods,
king race bearings supposed to be balanced to 10k...
Need help identifying an engine part. The part is right behind the fuel injector rail. It has a small hose connected to the air intake. See attached picture.
Clumsy me. I broke off the piece that connects to the air intake.
2005 Acura RSX Base Automatic.
Thank you very much for your...
So I pulled my k20a3, put the same motor back in and it cranks over but doesn’t sound like the fuel pump is turning on.. I checked the fuses and I’m going to check the power at the connection to the fuel pump and make sure.. but I think the engine harness that came with it is an automatic.. my...
I'm trying to perform a compression test on my 2002 RSX Type-S but I am running into a weird issue. The vehicle has no issue starting normally EXCEPT when it has been extremely cold here in the winter (-40). However it will not crank when I attempt to compression test it.
Following the factory...
Looking for the rubber hood hinge cover for the driver side hinge.
Dealer costs $16, but they are on back order, so no telling when they will have them.
this month or next year... lol
I'm in Minnesota, 55418
If your parting out your car, let me know if you have one..
First off sorry if this is the wrong place or if this has been covered I'm just a newbie.
I recently bought my first car it's a 2006 RSX base model. I couldn't help but notice it was missing the Acura and i-Vtec badges that are supposed to be on the engine. Any idea where I could get...
I got a k20a2 with 98xxx miles for sale. The car was wrecked and I only had liability. So ima make someone a deal of a lifetime. $1000 gets the engine and transmission. Throw in another $1000 and you get a Seibon CF hood, k&n typhoon short ram air intake(polished to mirror chrome, stage 2...
So I went to start my car up to run errands and the engine started making this noise as I was letting it warm up.
Oil was changed a few weeks ago and level is fine. No cabin vibration and was idling normally.
The car was driving fine just the day...
I was curious if anyone has bought braided loom by the foot and some cloth tape to refinish their OEM engine harness? I was considering taking this on versus buying the $600 Ktuned or other brand engine harness.
I was just looking for tips or how much you may have invested in it? I’m...