Search Results for ‘eps’

Hello again! I made a DIY of how to do the EPS conversion. I used an EP2 instead. The EP2 is the base model (European version) of the Civic Si we had in the States. I know this DIY it's been done by the guru @spaz :hb: long time ago but I just wanted to do my version. Enjoy!! PS: Please...

After removing the dash and reinstalling, the EPS no longer works and the EPS light is on. It gives 12, 16, 22, and 23 as the DTC's - all are related to voltage. The SRS unit is no longer in the car and the SRS harness leading to the belt tensioners and other SRS components in the cabin were...

Hello ClubRSX! I have scoured the bottom on the internet with no avail. I have swapped an EP3 EPS into my car, wired up, was running fine for a while. i am sure that the rack has a bad torq sensor thus the PCM is throwing a code disabling the rack completely. Since its swapped, there is no...

There is some elec power steering motor (sorry not familiar with EPS) with bars (tie-rods?) coming out into my hubs. There is a bushing on the tie rod end (I think that's what it's called) that looks like it's shot. I'm guessing this is why my steering feels like garbage when going from a left...

I'm currently looking for a place you mount the bcu or control module for my ep3 eps. Is it okay for it to be covered with carpet or does it need room to vent? Also does anyone have the female connecter for the white/blue wire? For constant power

do i need to have kpro in order to have this work? do i need the harness thats in the install? or can i just splice into my existing harness? what are all the parts i'll be needing? i have a parts car ep3 that i can pull everything from

As title states looking for Hasport 70a motor mounts as well as a full conversion EP3 EPS rack. Must be willing to ship, thank you ?

Have an extra EPS Passanger Side Bracket from my swap. $30.

Looking for complete EPS conversion! preferred closer to San Bernardino ca 92407 but I'm willing to pay for shipping if it isn't too much.

My EPS rack did not come with brackets. Is is possible to use the RSX rack brackets with the EPS rack?

Setting up EPS in my 06. Can the VSS #1 power wire (Yellow/Red Stripe: A21) be tapped at the jumper harness to the switched 12 V (E9 Ig1) or does it need to be tapped at the connector on the tranny? I would like to avoid running a wire from the tranny to the jumper harness.

I'm currently looking into getting an EPS setup. I have a question on the Civic Hybrid EPS steering ratios. Why do the 03-05 MT hybrids have a faster steering ratio than the 03-05 AT hybrids when the part numbers for the rack and BCU are the same?

Sold

Like the title states im looking for a bov, 44mm wastegate, 4 bar map sensor, intercooler and piping for sidewinder. I have a manifold and downpipe also have a boost controller already if there's anything else I need you may have let me know. please pm I'm open for trades or buying it thanks

Close

Like title states looking for eps wire harness don't need the brain or rack just need the harness if any one has please pm

EPS with brain but no tie rods and no plugs for $350. You have to use your rsx tie rods anyways or trade for ktuned full shifter setup.

Like title says EPS with brain but no tie rods and no plugs for $350. You have to use your rsx tie rods anyways or trade for ktuned full shifter setup.

Hey Guys, I'm looking into resetting my EPS BCU.. I installed the EP3 EPS System 3 years ago in my DC5 with no issues and just recently when I removed the rack and pinion to change up my inner tie rods everything stopped working. I have check voltage going to the BCU which checks good and...