my a3 has been boosted for over 25,000kms of dd use with no VTC issues at all it was just very sluggish in the top end like 5500 - limiter was painful so i decided to switch out the horrible 3 piece plastic intake manifold for a RBB 2 piece off the floor and put A2 cams with 2 sets of a3...

Hey guys total noob here. Does anyone have this headlight to bumper gap? its driving me crazy :rest Am i missing like a bumper clip to a headlight bracket :confused: Thanks if anyone could post picture or show me a video of where to clip these in that would be much appreciated.

I recently pulled off my window trim to paint and when i re-installed them I noticed a gap between trim and window. Some of the clips were broken. Will this cause the gap? Thanks.

I had to remove it to get to my cruise control module. And now I noticed the windshield panel has a slight gap when I put it back together. I tried different ways of securing it but still lies a gap. I'm just wondering is that going to be an issue come rain or washing it? That goes area goes...

question. just had my rear replica mugen lip installed with my buddy... fitment itself is pretty much bang on (just need to get a heat gun to fix small areas).. however when i used the 3m double sided tape to tape around my actual bumper, there are certain areas where it doesnt "stick" as well...

Hey guys, im new to the group but i have a quick question. I have a 03 rsx and my wheel gap from the tire to the door is different on the left than the right. On the driver side i can barely put my foot into the gap and on the passenger side my foot can fit. Ive done my alignment but that didn't...

i know it will be lower but does anyone have a picture or can help please?? i want to keep it semi oem but still wana remove some of the wheel gap...i guess i might have to get bigger wheels? =/ thanks for anyone who can help

Just put in a k20/24 and got everything running and working then i get the code for the vtc phase gap. I pulled the valve cover and can see that the colored chain links are not in the same place as i initially put them when building the motor, but i cranked it so that cylinder one was at tdc and...

Hey guys, I'm installing my manly pistons for a turbo setup.looking to get around 500hp+ I've looked on the manley info sheet and came up with a gap for the top ring which is .01523" (bore x .0045") and the second ring gap is .01185" (bore x .0035") my bore is 86mm or 3.38583". I was just...

I was wondering if anyone has ideas as to what I could use to cover the gap where my passenger airbag used to be? Basically, I took my airbag out and I'm trying to cover that hole with a cover of some sort. Unless someone is selling only the airbag cover.

Hi GUys does anyone know if there is such a thing to cover the surrounds of a double din multimedia unit? as you can see on my setup it has about 10mm gap around thanks guys

Just got my OEM trunk tray. In the back corner (drivers side) there is a gap. Any idea what this is for?

http://satg1.eventbrite.com Hope to see yall there :)

I see most of you guys run with a CAI. I have my car lowered on Tein H-Techs which drops it inch and a half but I want to go lower to the point where there is no wheel gap. My question is: Are you guys running no fender liner and riding with a CAI? I really don't want to remove that but "i need...

Very late notice and I'm sorry. But there is a group of us going around 12:30 (main group meeting in Polk Co. TN) and then riding up to Hwy 72 to pick up my woman figure around 1:30 (safe guestimate) and then hopefully on 129 by 2. If there is any interest post up and I'll get you some more...

What is the recommend compression ring gap for boosted motors?? I've searched and cannot come up with anything. I will be pushing about 16 psi.

I have a 2003 RSX Base with 125,000 miles on it. No mods completely stock. I have a CEL and its throwing codes P0341 and P0420. The CEL light turns off and on every other week or so... When its on the car runs sluggish.. when its off it runs normally. According to Autozone's scanner...