Acura RSX, ILX and Honda EP3 Forum banner

hole

  1. Exterior Mods RSX
    So i searched the threads and couldnt find any involving wing removal techniques. What Im specifically looking for is somebody who has done the job with good results that could share some knowledge. Id like to fill the holes and touch up paint if possible saving the costs of painting the whole...
  2. Problems & Solutions RSX
    This probably isn’t a big deal but I noticed a hole where the transmission (k20z1) meets with the engine (k20a2) near the half shaft (or whatever it’s called) and you can see the flywheel through it. Not sure if it’s supposed to be there or if a chunk broke off, never noticed it before. Maybe...
  3. Problems & Solutions RSX
    So I changed my clutch out and I just noticed a hole near my passenger axle...not sure what to do about it? The hole is the darkest area on the pic, it's about an inch long by maybe a 1/4 inch wide. Also noticed drops of oil at the flywheel inspection plate, at first I was thinking I screwed up...
  4. Problems & Solutions RSX
    Hi! Long short story I begin working on my RSX late last summer. I decided to keep the old thing and redo a entire brake and suspension swap with new parts. The only thing I didn’t replaced were my ingall rear cambers..... Soon to regret after installing everything I ran into a problem with...
  5. Suspension, Chassis & Brakes
    Hi! Long short story I begin working on my RSX late last summer. I decided to keep the old thing and redo a entire brake and suspension swap with new parts. The only thing I didn’t replaced were my ingall rear cambers..... Soon to regret after installing everything I ran into a problem with...
  6. Southern California For Sale: Local Pick-Up
    Hi SoCal, I'm selling my used but not abused DC5R K20A Spark Plug Cover Assembly and it comes with hardwares. Price is $10 pick up in 92629 or $15 shipped anywhere in the country. Actual pictures: Hardwares aren't included on these pictures but they come together as a set. Thanks Paypal ready
  7. Problems & Solutions RSX
    what up guys have a 05 type S and i just did a mm swap and while i was under the car i noticed a small hole on my transmission right where the transmission case meets the engine case, I am not sure what this is ? It doesn't look factory to me. All I can think is that its a hole so if the rear...
  8. Interior Mods RSX
    So I'm planning on running the wires to my satellite radio receiver under the dash to keep them out of the way, but need a way to kill power to it manually. My plan is to replace the front cigarette lighter with a power button that I can press to turn it on and off, since I won't have to mangle...
  9. Problems & Solutions RSX
    Got the k tuned 4-2-1 header and install is pretty easy once you take each section apart and it fits in between the sway bar like they say but they messed up and didn't drill the top left bolt hole in the right place so I'm leaking there. I heard you could burn a valve if you run your car with a...
  10. Problems & Solutions RSX
    What is this bolt hole to the right of the rad hose (red)? i assume its a mounting point? maybe for stock airbox (which i never had so i dont kno). also, as u see my IAAV is seeping some coolant (yellow). should i let it ride or just go ahead with the delete? it's barely glistening around the...
  11. Transmission & Drive Train RSX
    K20z1 stock tranny Is this supposed to be there or not? Flywheel is behind there, you have to pull the input shaft out to see it.. Been getting some mixed answers.
  12. Problems & Solutions RSX
    So i bought an 06 a few months ago and after browsing the boards here i learned that water in the trunk is a common problem with these cars. so i checked today and long story short : i was able to punch through with my thumb in a couple places.... don't even know what to do with this. I'm...
  13. Interior Mods RSX
    I was installing my BC Racing coilover extenders and didn't measure twice. Long story short I have a quarter sized hole in the drivers side carpet that covers the coilover. Instead of trying to patch it I figured I could make use of it. So far I thought of: An additional trunk light Flare mount...
  14. Problems & Solutions RSX
    Hey guys,gals at CRSX I've been doing some work to my Rsx, replacing thermostat, rad , vtech oil pressure switch ect. Anyways I came across this hole on the side of my block. It looks gummed up. I'm just curious if anyone know what it is. THANKS
  15. Problems & Solutions RSX
    didn't use my car for 1 week now that I try to turn on my car it doesn't want to, it cranks an its sounds like it's about to turn on but then it chokes I'm going to change my spark plugs an see if that helps ,but I was reading online that spraying starter fluid on the spark plug hole will help...
  16. Problems & Solutions RSX
    Hello, I have a 2006 RSX and it looks like there's a huge hole in the rear part of my front wheel wells where I can see the engine and all the way across to the other side. I think I read somewhere that their 2002 RSX type S has this as well. Sorry, I'm not very car savvy...but just...
  17. The DIY Garage RSX
    So I'm planning to take off my front license plate soon but I'm pretty sure there is a drilled hole in my bumper in the middle. Any simple suggestions to fix it? P.s My bumper is Milano Red
  18. Problems & Solutions RSX
    The lights that light up my speedometer and a/c gauges doesn't work, nor does my running lights ( tails ). Break light works, blinkers work, headlights work, reserve light works, hazard lights work. anyone have any suggestions? car is a : 2004 acura rsx 5 speed. :firemad: I donnno what to do...
  19. Problems & Solutions RSX
    Hey all!! I got to work this morning and when I parked I noticed there was What looked like steam blowing from the front of the car! Under further investigation The ac condenser has a dent/puncture and has released its charge! My question is is it ok to let this slide till next summer to fix...
  20. Problems & Solutions RSX
    I was replacing my knock sensor and got the old one cross threaded on the way out. Now the new one will only go finger tight, if I try to torque it down it just spins. Is there any way to fix this? Will loctite work? Sent from AutoGuide.com Free App
Top