Acura RSX, ILX and Honda EP3 Forum banner
hydraulic
1-20 of 30 Results
  1. Transmission & Drive Train RSX
    Hello, I have a 2nd gen RSX Type S. I got the car a year and a half ago during Fall. On early spring, my cmc blew, so I replaced it with a new em2 nissin one, but hastly bled the system. I adjusted the rod also, and shifting was smooth as butter, but after a couple of months, it came back to a...
  2. Problems & Solutions RSX
    After driving around a little I went to put it into first gear and it felt like it was hard to get into first but I thought nothing of it. Then when i went to lift my foot up off the clutch pedal it stayed on the floor. I couldnt get it out of first gear. I took my foot off the gas and hit the...
  3. Transmission & Drive Train RSX
    My CSC gave out a few months ago so I bought a new Honda EM2 CMC and CSC, replaced it, bled it, blah blah blah. Just yesterday I noticed the engagement point has been higher than I am used to but thought it was in my head. I got on the freeway and the clutch pedal seemed more stiff, like what I...
  4. Problems & Solutions RSX
    Ok so I've posted a million times about why my clutch feels like @ss and nothing. But in short I've had the clutch itself, master cylinder, and slave cylinder all changed out at around the same time. But my clutch has a lot of slack and is super soft. When I adjust the master cylinder pushrod my...
  5. Transmission & Drive Train RSX
    Parts: CC Stage 1.5 Clutch, CC 8lb Flywheel, OmniPower CMC Hey guys, I replaced my clutch awhile back with that listed above. Shortly after, my cmc went bad and i replaced it with the civic one and bought a new slave while i was at it. This lasted a little while until the same issues came...
  6. Transmission & Drive Train RSX
    Hey guys, So back in July I replaced my clutch and flywheel with the CC 1.5 and 8lb fly. Shortly after I could not shift, so I did some research and ended up replacing my CMC with the Civic one, and replacing the slave while I was at it. About a month later, I couldn't shift again. After...
  7. Transmission & Drive Train RSX
    Okay so I am having an issue here... One day i get into my car and the clutch feels just a little soft and i get a block down and i am unable to shift into 2nd gear, once into netrual i couldnt shift into anything, i got home by turning the car off and starting it in 2nd gear. Now pretty much...
  8. Exterior & Interior RSX
    hi, for my 2003 RSX Type S. i need the one for the passenger side - i'm not sure if they are the same on both sides. mine crapped out. :( i need a working one. pls let me know, thanks! kind of low on cash right now (unemployed at the moment) so if one of you guys can give me a bargain or...
  9. Problems & Solutions RSX
    So I'm trying to fix my buddys car for him and I'm almost positive I have it pinpointed but I'd like to see what you guys have to say... Symptoms: One day he was driving and all the gears started to get crunchy going into gear.. he parked the car for a bit and when he got back in he couldn't...
  10. Engine & Transmission RSX
    *** HOLDING for rabbit on K20a*** I have for sale a brand new Tilton Release Bearing. This was originally purchased as the entire kit from ClubRSX HERE. Unfortunately it did not work with my setup so I am only using the CMC portion of the kit. This unit has been installed for fitment and...
  11. Florida For Sale: Local Pick-Up
    BNIB 400 picked up Got Thread on k20a.org and FHC under dc5 roll call
  12. Engine & Transmission RSX
    I have the complete Power steering rack/pump from my car for sale. It's been packed away and I don't have any photos, for a serious buyer I'll snap some. 200.00 shipped
  13. Auto X & Road Racing
    Original Post at bottom of page. update: 10/7/10 Steering quickener custom assembly being prototyped. So far I am able to attach to existing steering pivot assembly. Instead of welding it toguether a hole and bolt will be used to secure the quickener rod to the steering column. This will...
  14. Welding, Fabrication, & Tools
    Old thread - don't bump
  15. Canada East: For Sale & Want to Buy
    I recently bought a new jack and have no use for this one. Reason for upgrading was so I could jack the car up higher, as the lift range on this jack is 12 4/5". Enough for you to change wheels, get underneath to remove bumper, etc. It's been used 4 times and is in pretty much brand new...
  16. Want To Buy or Trade RSX
    Hey Guys, Looking for a GSR hydraulic tranny in good condition. Let me know what you have and how much you want for it. Thanks.
  17. General RSX Discussion
    My wife's 2005 RSX-S (she babies it by the way!) has to have the (slave??) and master cylinders replaced due to leakage at about 75,000 miles. She was having a really hard time shifting into reverse and into one of the forward gears. I had her get the tranny fluid changed; did not make things...
  18. Problems & Solutions RSX
    this should be a sticky. since i've seen alot of threads about people having problems with there clutch and hydraulic system. with a little to no help at all. this should clear up some problems you might having +REP me if you want to :beerchug:
  19. Canada East: For Sale & Want to Buy
    http://forums.clubrsx.com/showthread.php?t=646638 Local pick up would be cheaper.
  20. Engine & Transmission RSX
    As title states I went to EPS, have my 2005 RSX-S Hydraulic Steering Rack for sale, it has 60,000KMs (Canadian) on it. Asking 175 o.b.o shipped...
1-20 of 30 Results
Top