Search Results for ‘imrc’

Just picked up a 2005 RSX with P1078 and P1077 codes. I purchased a new part 17120-PPA-A01, when I tried to insert the new valve assembly it would almost go all the way in, it was shy just about 1/4". When I compared the new an old parts I noticed that the new part has a plastic spacer and an...

Ok so about 8 years ago there was a post for this exact thing but the diagrams for how it's done have been lost. I've been trying to figure out how to replicate the success of the original circuit but haven't been able to figure it out as I am not good with electrical. The general concept, as...

2005 Acura RSX (Base) K20A3 Automatic Salvaged Title for 3 prior Accidents vehicle drives Great aside from Bad Wheel Bearing Used as a Commuter (weekly Mileage 458) So about a month ago i had to replace the starter so you know how much work that is you gotta remove the Intake Manifold to get to...

So I have a base rsx and got a smoke test done and it says it is the "imrc actuator" not sure exactly what the part is from looking online and how much it would cost or if I should just replace my intake manifold to solve the problem? Thabks if anyone can help !

While removing my intake manifold for a 2003 Base, I pulled the wires from the sensor. I depinned the plug but now I don't know what female terminal I need. Any help? I found a sumitomo female terminals on amazon. I believe it is pin 21 on the ECU yellow with red stripe VCC1.

Sup guys. Today I changed out my starter by removing the intake manifold. Unfortunately, as i'm still new to this car, I failed to check that all sensors were disconnected prior to removing the manifold. Because of that, I accidentally pulled the wires out of the sensor that plugs into the...

Should I replace the whole assembly or just the sensor The code reads intake manifold tuning valve control circuit low

I just changed my both 02 sensors, oil an atf the car hastn been running in 2 years now p1078 shows up what can i do? I need to pass smog.

Anyone have a picture of the wire harness that connects to the Intake Manifold Tuning position sensor or a wiring diagram? In my rush to get to the starter swapped for my sister I pulled a wiring harness. Got it back together but the harness only says Y, 12 and + . The colors of the wires...

Hey guys so I know there are a couple of threads about the CEL P1077 but most of them are 5 years old and don't have updates on what fixed the issue. Now that its been a long time, what is the final judgement on this? Based on my research, it essentially means 1 of 3 things: -Solenoid...

Thanks in advance for any info. So I replaced my starter. Now everything running perfect. But I'm getting a 106 cel code(I got it usingthe obd2 jumper method). Now I took the imrc solenoid apart by mistake( didn't realise it came apart the way it did) and the spring and small metal cup...

Looking for a imrc sensor for a 02 base. Can pick up. Pm is best

Currently testing a simple circuit prototype that allows the use of different intake manifolds on the base RSX without throwing engine codes. The circuit can be made in under an hr with a soldering iron and $11 in parts from amazon, ebay, radioshack or other electronic component retailers. I...

I was just wondering if anyone might be able to help me out with replacing my IMRC solenoid valve. just a step by step thing would be awesome. I know I would probably be looking to remove my front bumper cover and bumper bar to access it. but any body else with more knowledge on this then...

Basically, my car is throwing codes P0661 and P0178 and I need either the whole assembly or solenoid.

Please let me know what you got.

Ok so this is a long shot but I need the Pigtail off the harness that connects into the IMRC Assembly shown below for a base 2002... checked with the dealership.. dumbass did not even know what the IMRC assembly was even with the image in front of him...so please if anyone is parting out let me...

Selling the IMRC assembly for the base manifold. Bought it form a memebr thinking it was the problem turns out the pigtail from the harness is what's throwing the damn code...selling for $47 just getting back the same amount i spent ...thanx...

Selling the IMRC assembly for the base manifold. Bought it form a memebr thinking it was the problem turns out the pigtail from the harness is what's throwing the damn code...selling for $47 just getting back the same amount i spent ...thanx...