Acura RSX, ILX and Honda EP3 Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. Exterior Mods RSX
    Can someone with a oem type r wing please measure how tall it is I wanna make sure my replica is right before I send it off for paint.
  2. Suspension, Chassis & Brakes
    Soo....I been riding on raceland coilovers for about 3yrs.....I have no complaints for what was spent....and I only spent $300. I bought my 02 rsx-s with progress drop springs and struts were blown, and being a father of 6 kids and a stay at home wife, I was on a budget these coilovers. I...
  3. Suspension & Brakes EP3
    Does anyone or can anyone measure the jacking points on..... HFP ??? ASPEC ???? Type R ????? Or what's a good point to set them at? DD progress comp coilover Not looking for slammed low offset scraping the ground BS
  4. Lighting RSX
    I'm currently planning on either buying or making custom led boards to fit into the dome/map/trunk areas. I was wondering if anyone on CRSX knew the dimensions of each of the respective areas. I already know the "bulb" sizes of each location.
  5. Suspension & Brakes EP3
    Was wondering if anyone knows the measurements from one mounting hole to the other mounting hole for the rear lca to the other for a lower tie bar?
  6. General RSX Discussion
    Hey, can someone take measurements of the stock type s 2002-2004 gauge cluster for me? The length from left to right, The height up to down And the overall circumference Im seriously considering to attempt swap one into my car but I'm not sure if it will fit and I'd hate to buy one and then...
  7. General RSX Discussion
    Putting my emblems back on (don't ask why) and was just wondering how far is it from the edges? The ACURA and RSX that is. If anyone could go to their car and measure it, that'd be great :thumbsup:
  8. Suspension, Chassis & Brakes
    Could someone please give me the front and rear measurements to set these coilovers again? I put them on but lost measurements Also it seems that the rear right coilover is making a clunking noise when going over bumps. The collars and bolts are all tight and the spring preload is adjusted...
  9. Bolt-On Basics: RSX (Base)
    There seemed to be some disagreement regarding whether the base manifold was any different than the '05 Type-S beyond the angle/length of the collector and so when I installed the '05 Type-S exhaust system on my base, I measured both the base and the Type-S parts. I also included the...
  10. Suspension, Chassis & Brakes
    Pulls decently hard to the right but inconsistently. What i mean by that is it pulls hard right sometimes or just doesnt pull at all which is weird. I did a brake job a month ago so it might have something to do with that but just wanted to clarify that it wasnt the alignment. Dropped on BC N+
  11. Suspension, Chassis & Brakes
    I have searched the Helms and here looking for the OEM spec thread measurements for the tie rods. I am interested in getting the inner tie rod thread size and pitch- the thread that goes into the steering rack mount. The car is DD so I can not exactly miss work to take the tie rods off and...
  12. Supercharging RSX
    Header Collector inner Diameter: 2.83" Outer Collector Diameter: 2.95" Primaries Inner inlet Diameter: 1.616" Wide x 1.504" tall Primaries Outer Diameter: 1.632" Collector Primaries Inner Diameter: Unable to measure. They do not seem to shrink in size as they enter the collector. bends seems...
  13. Interior Mods RSX
    I am a big guy and I want to buy some seats and I really like the red recaros my question is.... what is the measurement of the lower cushion of the recaro... because oem ones are 21 inches... please help me out found a good deal on recaro's and dont want to pass out on them...
  14. Lighting RSX
    I've been asked a few time what the measurements are on the LED halos in the 02-04 Anzo Halo Projector Headlights. Now you can tell retro-solutions what size your halos need to be. Low Beam Outer: Low Beam Inner: LED Halo Width: High Beam Outer: High Beam Inner: Low Beam Trim...
  15. Turbo RSX
    I'm looking for an aftermarket fuel rail that will fit a very tight install on a car with a custom inlet manifold. The stock fuel rail fits, but I want to run a return line so I'd like an aftermarket one with -6AN or -8AN ports. There is not enough room at the left hand end of the fuel rail for...
  16. Bolt-On Basics: RSX Type-S
    I'm looking for the primary, secondary, collector neck down, and collector output size. All I can seem to find is lots of people saying "oooh, obx is crap" or "Obx is great bang for buck" but I can't seem to find measurements anywhere. If anyone can provide a link and or measurements, I'd...
  17. The DIY Garage RSX
    Honestly did not look hard enough... Does anyone have these measurements?... Much appreciated...
  18. Problems & Solutions RSX
    Does anyone knows the measurements on the rsx rear bumper? just trying to find out the shipping cost... any help will be appreaciated, thanks! :wavey:
  19. Problems & Solutions RSX
    Just wondering if anybody can help me with measurements on the stock rear bumper? I'm sorry for the horrible sketches. All I have is Paint at work.:( Measurements Between 1 and 4 (4 being same spot on opposite side) Between 2 and 3 Between 1 and 2 Thanks for any help guys!:thumbsup:
  20. Exterior Mods RSX
    i need some measurements of the cargo area of the hatchback of the rsx. i need to know what kind of room i have so i can build or buy a decent subwoofer box for my new solo baric. thanks!!
1-20 of 28 Results
Top