Search Results for ‘missfire’

So everything has been fine with my car until recently. It started to missfire really bad. I pulled the code and it said Missfire in Cylinder 4. So I did what anybody would do, I swapped coilpacks around to see if it was them. The missfire only comes at random ass times. It could be fine...

'02 - S w/ 132k My car, after sitting for a while (5ish+ hrs), will sit and have a random missfire when I start it. This lasts for about ~5-10 seconds and does not do it again until it sits for over 5ish hours. Sounds like a subi. I can tell, whatever the problem is, is getting worse. Codes...

hey guys i need some help here,, so last night i raced my poor thing , went over 130mph and then check engine light started blinking so i have like 4 codes they say miss fire 12n 3 and multiple miss fire shit,,, what should i do

I currently have missfire in all 4 cylinders and a random missfire code, changed my spark plugs, did a compression test (starting from cyl 1 - 204, 209, 190, 210 psi) so the engine seems to be in good shape for 150k miles, I also changed the coil packs cause I've heard of dc's coil packs going...

Getting a cylinder 3 missfire CEL. Did a tune up and swapped coils around to see if the code followed the coils. No dice. When its wet out the car will stall out when coming to a stop. It will start back up. It was a rainy day today and the car was acting up quite a bit. I scanned the car...

I have a missfire on cylinder 3. I know its the coil. Is the coil from the type s and base model the same coil? And will it work on a base model?

...

Hi everyone, new to the site. Awesome place. Anyways I just purchased a 2002 rsx type s, and I noticed today that the vtec seems to either missile or is cutting fuel, it bogs when I hit high rpm, and I just got the car, 83k on it however barely maintenance done, what should I replace? I'm doing...

About two weeks ago i sold my 2002 type-s and bought a 2006 type-s in toronto and drove it home to newfoundland, on the way home the check engine light came on and i noticed the car didnt idle right.kinda sounded like an exhaust drone on the highway but just when the car was ilding. Today i...

my cel came on i got it scanned said i had misfire in cylinders 1 and 2 i changed the spark plugs, light went off then came back on... what could be the causes of misfire? was just driving the car and my cel started blinking....?

so my JRSC car threw 5 codes about a week ago. they were: miss fire cylinder #1 miss fire cylinder #2 miss fire cylinder #3 miss fire cylinder #4 and random miss fire so i replaced the plugs and it went away for a week. now it is coming back and no matter how many times i reset the ECU it...

If you have a bent valve, any low compression, or mis-fire... the Acura dealer will charge you between 2000 - 2500 to fix the problem depending of number of bent valve. It cost Acura dealer 176.22 for parts (not relating to valve) 12.21 for each intake valve 18.64 for each exhaust valve...

I was driving around yesterday and got the CEL came on. I reset it (pulled ecu fuse) but it came back on; So I pulled the code and it was a 72 = P0302 = Cylinder #2 Missfire. Thinking I might have a bad batch of gas or just freakiness. I reset it; threw in some injector cleaner, and topped of...

I can feel my car slightly miss firing at idle sometimes. It happens the most in the mornings when the engines completely cold, but it happens during the day at redlights some as well. It's not a rough miss or anything. Most anyone wouldn't notice it if it wasn't pointed out to them. I just...

Well, I have had a CEL on and off for about a month now. I thought it might have been the downstream 02 sensor, but after I scanned it today I found out it is a missfire in Cyl #1. I pulled my plugs and looked at them and they all look the same and all look normal. It seems to run OK for the...

I took my car to a shop to see what was causing the CEL to come on, and they said its missfiring. Does anyone know how i can fix this, the shop spoke to kenji and he said it might be the e-manage. I had the e-manage updated with a new program because i had the old one. But sure enough the CEL...