Acura RSX, ILX and Honda EP3 Forum banner

piston

  1. WTB k24 con. rod / piston / cam for Forced induction

    Want To Buy or Trade RSX
    I need Brian Crower Stage 2 Forced Induction k20a Type S 2004 or equivalent (short duration, long lift) I need pistons 88mm bore, C.R. between 11 and 12:1 (k24 2001) I need Forced Induction Connecting Rod 18psi (k24 CRV 2001)
  2. Rear brake caliper piston sticking?

    Problems & Solutions RSX
    I just washed my car and cleaned the wheels really good (stock 05'-06' Type-S) but after a couple days of driving my drivers side rear wheel is coated in black brake dust while the other wheels still look really clean. It's a 03' Type-S with 136,000 miles. How can I fix this or do I just have...
  3. Piston compression for boost?

    Turbo RSX
    I searched for days for the answer to this finding no real solution. What compression pistons is everyone running with their turbo set-up and what fuel? I am going with a basically a GT35r turbo and I'm at sea level. I can't decide if I want 9.0:1 or 9.8:1 pistons for my engine. The 9.8:1 are...
  4. wtb FD2 Civic Type R Piston Set

    Want To Buy or Trade RSX
    im looking for fd2 oversize pistions
  5. Turbo piston advice

    Turbo RSX
    looking into getting CP pistons for a turbo setup, I've read some good and bad reviews just wondering what you guys think about them? let me know please and if you have any other recommendation Thanks
  6. Worn piston rings? Bad exhaust valve? Need valve adj?

    Problems & Solutions RSX
    Ok...here's the story. I've been dealing with this misfire since I bought the car two years ago. After changing the spark plugs and the ignition coils, nothing. After switching fuel injectors, spark plugs, and coil packs nothing. So then we did a compression Test. Only bad compression was the...
  7. Is this brake caliper piston retracted all the way? QUICK ANSWER NEEDED

    Problems & Solutions RSX
    I am installing the powerslot rotors I picked up from kseriesparts the other week, and I do not have enough clearance to reassemble the rear calipers. However I am not sure if the rear pistons in my back calipers are retracted completely. I have broken a screw driver and a chisel already and I...
  8. ...

    All Motor RSX
    close
  9. JE Piston, SS clutch line, PS delete EP3 pulley/belt, and Nose bra only!

    Part Outs RSX
    I'll get some pics up tomorrow JE Piston 9.1 - $225 Used! Good condition, need new rings! SS clutch lines only (Black ONE ONLY)- $55 No fittings. Line ONLY! EP3 pulley and belt setup- $110 Power steering delete! Good conditions! Brand New nose bra only! - $85 NO pic of the BRA! Sorry...
  10. Piston Swap.

    Engine Building & Design
    Im new to the site new to k series iv searched for two days now and havent been able to find exactly what im looking for im rebuilding my motor since im at 200k im just doing a basic rebuild but would like to upgrade compression to 11.5:1 or maybe alittle higher i run nitrous and its a daily...
  11. Close

    Suspension & Brakes RSX
    I'm testing water on my bbk kit see if there's any interest in them. They have around 3k miles on them. These are not the regular bbk wilwood has there the 6 pot ones and hard to find for the rsx Kit comes with everything to install
  12. Close

    Northern California For Sale: Local Pick-Up
    I'm testing water on my bbk kit see if there's any interest in them. They have around 3k miles on them. These are not the regular bbk wilwood has there the 6 pot ones and hard to find for the rsx Kit comes with everything to install
  13. Fs: Bnib 6 piston bbk

    Canada East: For Sale & Want to Buy
    Selling a set of Neo Motorpsort's Big Brake kit for the front and rear. This kit will fit any rsx 02+, tsx 04-08, civic 06+. The Rotors are two piece 13" Cross Drilled and Slotted. The front caliper is 6 piston ultra-high strength forged 6061 alloy aluminum anodized orange. The rear caliper is...
  14. Rear brake piston popped out

    Problems & Solutions RSX
    Hello, I've been a member for quite some time now and this is my first post. Whenever I have a problem with my car or just want to read about others' experiences with their cars, this is the place I would come to. But now I have a problem that I could not find an answer to. First off, my car...
  15. Please help quick! Brake piston boot.

    Problems & Solutions RSX
    Long story short, the piston was pressed out too far and one side of the piston boot is sticking out while the other half is pressed up inside of the housing like it is supposed to be. What can I do to get the rest seated like it is supposed to be? I'm running out of day light and not able to...
  16. k20a itr piston part number

    All Motor RSX
    trying to find out the honda oem part number for itr k20a pistons standard size and piston ring part number
  17. Stock strut piston diameter?

    Suspension, Chassis & Brakes
    Hey guys, Im having some adapters made for top hats for someone and I need to know the diameter of the strut shaft where the OEM top hats slide on. If anyone has one laying around and could measure with a dial caliper I would forever be in your debt. I need the measurement to .001" accuracy.
  18. Interchangeable Piston Rings/Bearings?

    Engine Building & Design
    Had a buddy order me piston rings and main/rod/thrust bearings for my 02 RSX-S, he works at Acme Auto so its not Honda brand, it's one of their suppliers, can't think of the name. My question is, all the boxes say either K20A3 or 02-05 Civic, will these all fit with my block? As soon as I saw...
  19. TSX K24a2 piston selection help

    Engine Building & Design
    I am trying to pucrhase k24a2 pistons from the dealer and I am noticing the difference in part numbers for the oversize .25 pistons throughout the years. 2004-2005: 13030-RBB-010 2006-2008: 13030-RBB-A00 2009-2012: 13030-RL5-A00 So I know that the newest tsx pistons have a 11:1:0 compression...
  20. Type S brakes -> 2 Piston RDX/CRV/ODSSYEY Calipers

    Suspension, Chassis & Brakes
    Type S brakes -> 2 Piston RDX/CRV/ODSSYEY Calipers After talking to Honda Josh Aka "Drivetofast" I decided I need better brakes. Well since i am saving for a C38-91 Rotrex, i decided i needed something economical. So Josh suggested to use the 2 Piston rotors From a 08+ CRV. Josh did a little...
Top