Acura RSX, ILX and Honda EP3 Forum banner

question

  1. The DIY Garage RSX
    I bought the ktuned power steering pump fitting for my 03. Does any1 know what fitting is needed to adapt off the rack? Is it 3/8npt?
  2. New Member Introduction RSX
    I was rear ended and had to replace the tail light and bulbs but i bought the 925 bulb and it smelled burnt and smoke came out yesterday after i replaced it and turned on the car.. any ideas what it could be? i dont think its the wrong bulb unless im supposed to use a 7440 bulb? Could it be...
  3. Lighting RSX
    My headlight bulbs have wiring like this: Any suggestions on the best way to connect that wiring to the 3 prong female end on the wiring harness? Currently, I just have the ends shoved in to the appropriate power and ground spots on the female end, which works in terms of powering the bulbs...
  4. K-Series Swaps
    Hi I’m new on here and I own a 2004 Rsx type S it’s also my first car. Long story short a month after buying the car the engine blew after taking it to a shop for an oil change. I never got to know why it blew but I took the opportunity to change things up so I bought a K24a2 of a tsx. The car...
  5. Transmission & Drive Train RSX
    Hello, I just replaced my clutch/flywheel. There was a 17mm bolt that I believe went through the starter motor that I stripped pretty bad. I was able to remove the bolt, but I want to replace it with a new one. I have searched through many part lists, I am having trouble locating this bolt. I...
  6. Problems & Solutions RSX
    hey idk if anyone followed the thread i had in the diy section but i've got almost all my sound system done up i just had the following question: do the factory tweeters work with aftermarket stereos? i lost the diagram that came with my metra adapter harness and im not sure if they never worked...
  7. Turbo RSX
    Hello everyone, greetings from Panama friends ... I am building my project of the DC5 base 2002 K24A2 Turbo sidewnder Automatic. The ECU does not worry me much since I will adjust with Ktuner for 05-06 + the Harness for 02-04 ... I have the opportunity to get a TSX transmission, the question...
  8. New Member Introduction RSX
    I’m looking for a hood and a single headlight assembly for my 2002 rsx premium. I’m on a very limited budget, like almost non existing so I’m needing pick your own part prices but if they don’t have any Rsx’s there can I simply just grab a hood or headlight off of a same year civic?? Maybe a...
  9. Problems & Solutions RSX
    Swapped a 06 tsx k24a2 into my 06 type s just bought Ktuner to run a tsx base map now problem I’m having is everyone says as soon as you plug the Ktuner to the obd reader a prompt is suppose to come up saying “would you like Ktuner to lock ecu?” And that registers your Ktuner but that prompt...
  10. Bolt-On Basics: RSX (Base)
    Is it possible to swap a type s TB and IM onto my base without hondata or tune? Sent from my iPhone using Tapatalk
  11. Lighting RSX
    I hooked up my OEM fog lights over the weekend, and followed the instructions, question is. The lights only come on when i have the head lights on, is there a way to change the wiring to have them able to come on while the parking lights are on ? Thank you. problem solved.
  12. Suspension, Chassis & Brakes
    So I’m looking on a San Diego DC5 club page and someone is selling a set of coilovers (buddy club) with adjustable dampening. He says the rears are fine but the fronts are stiff, and he said it could be due to him maxing the ride hide down to its lowest point. So my question is, could it be that...
  13. Problems & Solutions RSX
    I have a question and can't seem to find the answer.. On my 2005 Type S i've always used the IFR7G-11KS Laser Iridium Spark Plugs, but i was on the autozone website and others and i saw the PFR7G-11S Laser Platinum Plugs.. (i've researched and seems they are for S2000) and it said these were...
  14. Suspension, Chassis & Brakes
    I'm currently installing a set of BC Racing coilovers on my 03 type s. I've got the rears done so far... I forgot to get a tie rod tool prior to starting this project so the fronts are on hold at the moment. I was looking at the front end yesterday and my tie rod ends look like garbage and need...
  15. Bolt-On Basics: RSX Type-S
    Hello guys, I'm planning on ordering some Hasport 62a motor mounts and I was wondering if I just replace the rear motor mount would it prevent a race header from banging or do I also need the 2 front motor mounts?
  16. Wheels & Tires
    So I want to order some ESR SR08 rims, 17x9.5 +20/ can I go wider rims in the back or will anything bigger than 9.5 look dumb. I want my fitment flush. Tires: nitto neogen 215/45 Coilovers: bc racing My question is, if I was to get wilwood front calipers would the rims rub against the calipers...
  17. Turbo RSX
    Since I just upgraded my turbo I was thinking of doing a return fuel line. So this is what I was thinking of doing: Existing line leave alone as the feed Run a new line for the return from the FPR Here is my question: I was thinking to drill a hole in the top of the gas tank right next to the...
  18. Turbo RSX
    So far two on 2 civic si 2006-2011 8th gen I have had the cars jacked up and spun one tire and the tire spun in the opposite direction. I know that is clear for an open diff but what are the chances someone pulled the lsd out of both. Is the lsd only engaged when needed? I just want to know if...
  19. Transmission & Drive Train RSX
    Ok so I know there’s a search button I tryied searching but I just can’t read all this stuff and weed thrue I had neck surgery this last surgery so all I can do is lay flat and use phone so no I did not put much effort into researching But if people could help Me that would be awesome I’ll keep...
  20. Suspension, Chassis & Brakes
    Hey what’s up. Long story short sold my old car with itr brembo setup all around. Bought the car back with oem knuckles and lca. My question is...Is there anyway to tell if I have 02-04 or 05-06 knuckles. I need to replace a wheel bearing but I’m gonna replace the ball joints and control...
Top