Just recently got my first dc5. Is slammed on raceland coilovers. I'm happy with that but obviously need to fix the tie rod angle. So opinions? Drill out hole and flip tie rods? Buy inverted? Buy bracket? If so where to buy? Thanks for any input

I need help removing the inner tie rods on my 05 RSX! I tried looking everywhere for a DIY forum on the subject but couldn't. Is it absolutely necessary to remove the steering rack in order to get access to the inner tie rods? I understand that you're unable to fit an inner tie rod removal tool...

I am selling virtually brand new Pauter Rods and JE Pistons. Pistons are 9:0:1 compression. These items have about 6 hours use. Unfortunately I spun a bearing and had to abandon my project. To that point, one of the rods will need to be machined out to remove the material where the bearing...

Exedy Master cylinder never used: $30 shipped Exedy Slave cylinder never used: $30 shipped Honda tie rod ends never used: $60 shipped Stock air intake filter never used: cost of shipping + $5 Thanks for looking PM, text, or reply below 8645979908

I searched and was not able to find any reviews of the K-Tuned tie rods. They're quite a bit cheaper than the ones from dvrace. So are the hardrace tie rods. If anyone is using either dvrace alternatives I just want to know if you feel they are sturdy and appropriate for a type s that is...

I am looking for 06-08 RBB or 09-11 R40 rods. If you have them, let me know.

hey guys, i need to change my tie rods and im wondering whats the best way to do it. im dropped about 2"-2 1/2" with h&r coilover suspension. i need to change my tie rods as they are worn out. ive been getting mixxed reviews on oem tie rods or inverted tie rods. which tie rods would you...

0857s or T1Rs new or used, pm me if you have them, not tryna drop $240 for new T1Rs lol

So i have an 02-04 and i have yet to see it with a cut rear bumper with a top1 diffuser. I found pictures of and 05-06 cut with a js diffuser but cant seem to find one with an 02-04. Anyone think it would look good like it does with the js diffuser. Pictures of 05-06 Also planning to get a...

As the title states, will these fit STD sized bearings and oem crank? Like can I just swap them right in place of the oem rods? All help is greatly appreciated...

THIS STUFF IS ONLY COMPATIBLE WITH A K20, NOT A K24. Hey guys, I've decided to go a different route with my build so I am no longer in need of these. Wiseco 86.5mm 12.5:1 CR +10.5cc dome pistons with armor glide, these are brand new and still in the packaging, comes with rings and everything...

Im looking for todds tie rods if any of you guys local are parting out to sell. Prefer local, if not then i will get new later. Text me at 647 8.6.6. 42..16 Or pm me.

I am looking for todds tie rods. Willing to ship to Toronto, Ontario, Canada

Hey guys, Looking for a pair of Todd's modified tie rods for my DC5. I'm based in Western Australia and would be happy to pay the shipping cost. Cheers.

I just installed a set of Koni's with Todd's V2 Caster Camber plates. I have the Camber set to minimum, and the ride height is at about 14" hub to fender. There's so much toe in that the car is basically undriveable. Has anyone used this setup before with stock Tie Rods? I can't use...

Anyone tried these support rods for the top one splitter. Car is isn't tracked or anything. http://m.ebay.com/itm/Set-2Pc-Front-Rear-Frame-Bumper-Protector-Lip-Rod-Splitter-Strut-Tie-Bar-Support-/271792213968?nav=SEARCH Want it to look like this

sup guys so i have some OEM TSX parts, not to sure on what they go for so i am open for some offers but please dont low ball. i bought a tsx long block the was over heated. i cant tell u anymore info then that cause i my self dont know. but everything seemed to be ok when i was taking the...

I am looking to run 3+ degrees of front camber for autocross and need shorter tie rods or Todd's adjustable tie rods. I am hoping to find a deal on some used ones rather than pay $270 for a set from Todd.