Acura RSX, ILX and Honda EP3 Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-17 of 191 Results
  1. Suspension, Chassis & Brakes
    Hello, The DC5 Type R Brembos on my car are only about 1-2mm from the rims (in front, of course). The clearance is pretty close to even from the top to bottom of the caliper; the shape of the inner face of the rims is similar to the outer profile of the calipers. The car will be driven on a...
  2. The DIY Garage RSX
    This information is intended for an installation using a Compustar CM7200 Remote Start module (With Blade-AL security bypass), with the Alarm Kit (DAS) add-on. This information should be identical or very close for other modern Compustar modules. You can reference the materials that have come...
  3. All Motor RSX
    So guys I have a higher mileage RSX Type S(180k). Its an 02 and Ive been considering adding the Kelford Stage 1's to my xmas shopping parts list. So far Ive ordered the Skunk 2 Alpha Header, Invidia Q300 exhaust, Injen CAI and Ill be having K pro installed as well. Would it be safe to add the...
  4. Problems & Solutions RSX
    i just changed my spark plugs and the 4th had a melted ignition coil rubber boot. i successfully removed it and replaced the spark plug. is it safe to run without that rubber boot on the bottom of the ignition coil ?
  5. Turbo RSX
    is it safe to run on 6 lb. of boost on a base model rsx?:)
  6. General RSX Discussion
    Is it ok to run 6lb of boost on a stock motor on a 2003 base model rsx?:)
  7. Problems & Solutions RSX
    So i recently bought a PLM header for my DC5. I currently have all 4 innovative 75A mounts installed, with the PLM being bolted to a Greddy EVO 2. My question is, will the combination of having motor mounts, and using spring bolts with the donut gasket( @ header to test pipe connection) be safe...
  8. ECU Tuning RSX
    Sorry ment similar Hello everyone I have been reading and trying to find a kal comparable to what I have but no success. Im looking for a version 1 kpro and I have a k20z1 cai rbc manifold buddy club header and stock exhaust. Can any one help me out??? And does anyone know if the base map with...
  9. Bolt-On Basics: RSX Type-S
    ...going for around 200 bucks... what do you guys think? just want to improve performance alittle bit over stock by discarding my cat.:D
  10. General RSX Discussion
    .... the waterpump and alternator are original? :confused: How about the serpentine belt and valve settings? :( I'm only planning on going 3,000 miles round trip, what could go wrong? :mad:
  11. Problems & Solutions RSX
    So my check engine light came on the other day, and when I got it scanned, code P0134 popped up, which of course is the primary O2 sensor. After I got it scanned and drove to a gas station to fill up gas, I shut off the car, filled up the tank and started up the car. The CEL turned off. Today...
  12. Bolt-On Basics: RSX Type-S
    i have an aem air filter (cylinderish shaped) from my civic, which also is for accord. ive seen this done before back in the day with some of my poor friends and now with car payments im poor too :P would it b safe to just put the cold air intake filter on the stock intake piping? i know it will...
  13. Car Audio, Security, & Electronics RSX
    Is it ok to hook up speaker wire from the amp to my crossover unit which came with my component speakers? Or I can only power components by powering the factory wires? Thanks
  14. The DIY Garage RSX
    Is this the safe way to install the battery cable without having to drill a hole? Will the door opening and closing be a problem?
  15. Suspension, Chassis & Brakes
    Hello everyone, since Club rsx is out of stock on the new skunk 2pro c coilovers, I found some on eBay for about the same price. My only concern is, are they legit? And not those replicas people get scammed for. How can I be confident that its the actual product and not a replica.
  16. Car Audio, Security, & Electronics RSX
    I have a set of Bose speakers from my dads infiniti qx4 that I want to fit into my rsx. The corners are not rounded but I figured if I cut them it would fit into the panel. Would it be save to cut the edges to make it fit?
1-17 of 191 Results