Acura RSX, ILX and Honda EP3 Forum banner
size
1-20 of 500 Results
Advanced
  1. General RSX Discussion
    Hey there, I'm not too knowledgeable when it comes to wheel stuff but I had a quick question to ask. Does anyone know if 18x9+22 wheels fit an RSX good without having to modify anything such as camber and what not? I plan on lowering my car right after getting wheels too on coils (I want an...
  2. The DIY Garage RSX
    Do you think people can't time travel?? Hold my beer!!! :D ... We are back with the last episode of the series "Bringing back the RSX". Just an small recap... I decided to create these series of episode to bring you all a lot of info of to fix maintenance issues before inspections. Don't miss...
  3. Transmission & Drive Train RSX
    Hello, I just replaced my clutch/flywheel. There was a 17mm bolt that I believe went through the starter motor that I stripped pretty bad. I was able to remove the bolt, but I want to replace it with a new one. I have searched through many part lists, I am having trouble locating this bolt. I...
  4. Bolt-On Basics: RSX Type-S
    What would be the best size intake manifold and throttle body for 02 type s
  5. Wheels & Tires
    I'm ordering RPF1 17x9 +45 square set up. Got the hub centric rings 64.1 to 73mm hub rings. Will have fenders rolled. 1. Told I need spacers for rear, at least 10mm. Anyone have this setup who can comment? 10mm enough or more? 2. Does front need spacers?
  6. Wheels & Tires
    If I could get some help from those who have ran 18'' RPF1, 02 RSX on coilovers, planning on rolling fenders. Planning get 18'' RPF1, squared setup. What width and offset did yall run to have it fit without any major mods, were spacers or extended lugs needed? wanted to be more conservative...
  7. Interior Mods RSX
    Im in need of help. Anyone known the thread pitch for the poem bolts that hold down the seat to the car frame thanks in advance
  8. All Motor RSX
    So I'm currently running a 2006 Acura RSX Base Model and I know that the spec for the stock injectors is 270cc/min but when I looked up a chart for sizing injectors that seemed way too high. It seems like it should be closer to 230cc/min. Help please!
  9. Turbo RSX
    Hey I just have a simple question, I am getting a parts list together for a 2004 base RSX K20a3 engine turbo build. I already know I'm going to go with a set of 10 to 1 pistons ( haven't decided which brand yet ). My question lies with the decision of what millimeter size to go with? And yes...
  10. Bolt-On Basics: RSX (Base)
    Just wondering what size fuel pump is in the 2006 rsx base? And whats the biggest size injectors you can run with the own fuel pump?
  11. The DIY Garage RSX
    My previous oil change, I did it at the dealer and now I want to change the oil my self. I got an oil filter wrench that fits the new Honda oil filter (15400-PLM-A01) I want to put in, but the wrench is too big for the oil filter installed now. What acura/honda filter did the dealer put in...
  12. Exterior Mods RSX
    Looking to get some input on rim size I should get for my 03 rsx base model
  13. The DIY Garage RSX
    Working on the big 3 upgrade. There are two wires at the positive battery terminal, what is the gauge? I read it might be 6? Thanks in Advance!
  14. Wheels & Tires
    Looking to swap out my stock rims for a aftermarket set however im not sure what sizes fit this stock car without rolling fenders etc. looking to stick with 17s or go with 18. I know our stock size but I’m not sure what really works best. Any help would be appreciated. And yes I’ve tried...
  15. Wheels & Tires
    What’s the best fitment on it , and tire size recommend on this .. ??
  16. Problems & Solutions RSX
    I’m going to buy new front brake pads but google made me a bit confuse. There is one seller on ebay au selling brembo front pads that are 136.4 X 57.8. Then i checked on RockAuto they have front as 136.5 X 57.8. .1 is not a big difference but then i saw front’s for Type-S that are 135.1 x 52.1...
  17. Problems & Solutions RSX
    Hi, i want to double check, as i tried to google it but couldn’t find an appropriate answer. What belt size does Base RSX k20a3 engine take? This was the first time i changed since I bought the car, i ordered it through local store Autobarn here in Melbourne, Australia and they supplied me...
  18. Exterior Mods RSX
    18x9.5 klutch sl5 wheels came with 3 tires 2 215/40 and 215/30 I bought another 215/30 mounted the tires lowered the jack from last wheel mount and pssshhh tire popped of beam got it re mounted drove around corner same tire went flat I don't want stretched tire I want functionality so will...
  19. Auto X & Road Racing
    Hey guys, Im in a bit of a pickle. I have a buddy club wide body kit on my car. So naturally I went balls to the wall on my rim choice 17x10 +18 with a 275/40 r888. I've nothing but issues with the tires rubbing. I know what their rubbing on (pinch weld in the wheel well). I could just hammer...
  20. Wheels & Tires
    Hey guys, Im in a bit of a pickle. I have a buddy club wide body kit on my car. So naturally I went balls to the wall on my rim choice 17x10 +18 with a 275/40 r888. I've nothing but issues with the tires rubbing. I know what their rubbing on (pinch weld in the wheel well). I could just hammer...
1-20 of 500 Results
Top