Search Results for ‘spraying’

having a problem with my supercharged meth setup. im spraying 975mL (15gph) of meth. i began pulling fuel units via the nitrous perameter but i cant seem to really figure out whats going on with the AFR. i was never really seeing a change in it that would indicate to me that the meth was...

I figured it was bad pumps so I replaced them. I can hear both the pumps working when I activate them from the console so I know the fuse is ok, but no fluid comes out either front or rear. The driver side nozzle will bubble up and nothing happens on the passenger side. What am I doing wrong...

didn't use my car for 1 week now that I try to turn on my car it doesn't want to, it cranks an its sounds like it's about to turn on but then it chokes I'm going to change my spark plugs an see if that helps ,but I was reading online that spraying starter fluid on the spark plug hole will help...

I installed Rc 650cc injectors today and I have 2 injectors tthat are not spraying at all. When I take them off I hear compressed air shot out. I moved them ddifferent parts of the manifold and ithhappens every time. I bought these used off clubrsx, was told they only had 5000 miles on them...

I cannot figure this one out. :confused: After a hard pull, my coolant reservoir is filling up so much that it is spraying coolant everywhere from the breather at the top of the can. In the past, I had a smaller can. It would spray coolant after every hard pull. It would suck most of the...

Alright crsx I need your help. I installed kelford cams and rc 750cc injectors yesterday. Cams went in fine, tdc was a pain but we got it in the end. The injectors though on the other hand is where the problem is at. We wired in the pigtails for the new injectors just fine. But when I try to...

Hey guys, I just moved to Seattle and I'm trying to close on a house. All my tools are in storage and I don't have a garage for the next couple of months. Wonder if you guys wouldn't mind giving my your diagnosis. I've got an oil leak comming some where from the back driver side corner of...

I just went back to stock from a turbo setup, i took off all my turbo parts and went back to stock, and the only thing electrical that i touched was rewiring my stock injector clips back in and replacing KPRO with stock ecu. Now the car wont start, it cranks but doesnt fire. At first i thought...

i noticed the other day my washer fluid is not spraying since around when i cleaned my cai filter. i checked the plugs on the pumps and they seem fine, and i tried looking for a fuse for the fluid but only found the fr/rr wiper fuses. the wipers work fine but just no fluid and it is full. where...

im a first time booster who is also considering spraying. but i have no idea of the effect it might cause on my turbo. is it just safer to turn up the boost, and stay away from nitrous?? or will me spraying have no "major" effect on my turbine?? i'm looking at a 50 shot, just to have a lil edge...

I need tips, all the info I can get on what I need to be aware of when using k-pro + juce. Let me know

I don't remember who I spoke to through pm's a month or two ago, but I was wondering if anyone is running just nitrous with their Kpro what is your A/F ratio while spraying? Also I was wondering if anyone was running a wet shot, if you added any fuel in the nitrous table on Kpro or just put...

Here's my story fellas. I had a greddy kit on stock internals and it ran awesome! I got 303whp sae corrected on a dyno jet and 270tq. ANyhow, after boosting hard and reving to 9K on stock internals, one of my cylinders lost a little compression due to a piston having a little crack in it...

50 shot, running with a JRRH or DCRH. I talked with warmpepsi about this being a problem... Anyone else have any imput? Possibly safer with a h/f cat? I would havta get the o2 sim to eliminate the cel due to RH and all that shit messing with the ECU and then spraying. So anyone have any insight...

i have had my nitrous on my car for about 2 months now. i have been controling it through k-pro for about 2 weeks now. i've been activating it at 6 grand in 1st, and never spray past 4th. i bumped it up to a 75 today am going to have it activate at about 5500 rpm in first up to 8000rpm in all...

If any of you guys have a vid where your using the bottle please post it.I've never used or been in a car that was using the bottle and would like to hear the engine and see the acceleration difference.It may be my next step in the quest for speed.Thanks.

what do i need to do to spray the engine bay of my car? do i need to cover anything up, or use anything special? I was just going to take it to the HP one and use the pre-soak(really low pressure) and then spray it off with the rinse one, but what all do i need to "prep" for this? thanks

just curious to know if anyone has done it with a 50 or above.

When washing my car, I have a really hard time getting low enough with the hose to get the underbody. I know the underbody really needs a good cleaning, after this winter and all the salt on the roads. Anyone else worry about getting the nooks and crannies underneath? Any advice on how best...

How long has everyone been spraying ??? Shot, and how long can you go on a bottle (time wise)