Acura RSX, ILX and Honda EP3 Forum banner
stripped
1-20 of 111 Results
Advanced
  1. The DIY Garage RSX
    I recently purchased a 03 Type-s and about 2mths later the alternator went out. Long story short I got the belt off (not completely) and was able to swap the alt’s. Putting the belt back on my 14mm wrench is just turning on the bolts head. I will get this replaced but right now I just need to...
  2. Problems & Solutions RSX
    While tearing down this monstrosity of a mess that is this K20A2 I bought, I have a few issues with some bolts. The Hex bolt in the head that holds the rear guide is stripped. My first initial thought was stuffing the biggest extractor into the 6mm hole and giving it hell, but im afraid that due...
  3. Problems & Solutions RSX
    Purchased and installed K-Tuned IAA delete kit. Did not put threadlocker or Teflon tape on the screw. Removed screw to seal the leak of coolant coming thru. Screw comes out, all threads are destroyed. Wtf. I read on that this style screw is not supposed to be tightened past a snug figment , with...
  4. Problems & Solutions RSX
    Hi! Long short story I begin working on my RSX late last summer. I decided to keep the old thing and redo a entire brake and suspension swap with new parts. The only thing I didn’t replaced were my ingall rear cambers..... Soon to regret after installing everything I ran into a problem with...
  5. Suspension, Chassis & Brakes
    Hi! Long short story I begin working on my RSX late last summer. I decided to keep the old thing and redo a entire brake and suspension swap with new parts. The only thing I didn’t replaced were my ingall rear cambers..... Soon to regret after installing everything I ran into a problem with...
  6. Problems & Solutions RSX
    The car is stripped out, nothing is except some parts of the interior harness. Part of it is cut(from dash) Is there a way I can send power directly to the windows to roll them up and same for sunroof so I can take it off. Not sure if I can take sunroof without rolling having it up and open
  7. The DIY Garage RSX
    Ok so my tensioner pulley bolt is pretty stripped up, but can still be moved back and for with the tensioner tool and a 14 socket that is six point. Anyhow I wanted to change out my Ac compressor but don't wanna risk not being able to pull that bolt loose and tight. Also I just bought a new oem...
  8. Problems & Solutions RSX
    Hi all, my passenger motor mount is broken so I bought a replacement for it. Only problem is there's a nut that won't budge at all. We tried a box wrench, pliers, ratchets, putting WD40 on it to loosen it up and I'm at a loss. If anyone has tips on getting this taken off I would greatly...
  9. Problems & Solutions RSX
    today i was going to change the spark plugs on my 2002 rsx base. i was trying to remove the plastic cover to get to the spark plugs but the little bolts dont come off. they just keep turning and turning . how can i get them out ? the 2 bolts are circled in the picture. thanks!
  10. Problems & Solutions RSX
    today i was going to change the spark plugs on my 2002 rsx base. i was trying to remove the plastic cover to get to the spark plugs but the little bolts dont come off. they just keep turning and turning . how can i get them out ? http://imgur.com/4Hadkd8 the 2 bolts are circled in the picture...
  11. Problems & Solutions RSX
    I have been a long time clubrsx user and have followed many of your guys advice which has proved extremely helpful with doing all the maintenance and troubleshooting for my car. I just want to say thanks for all of the advice as this is one of the best car threads I've been on! As for my...
  12. Problems & Solutions RSX
    so I let my kid do his first oil change, and before I could stop it, he cranked too hard when tightening it up. To make a quick fix, I used an oversized drain plug. That seemed to work, but I ended up still getting a leak. So i have a few options: 1. Double oversized bolt. I really don't...
  13. Interior Mods RSX
    I want to install my aftermarket steering wheel but I stripped my torx screw . Any suggestions on how to take it out? :rest
  14. Problems & Solutions RSX
    So I have two stripped bolts on my stock catalytic converter. What can I do to fix it? Can it be removed? Is it wielded in there or something? Tried to hammer it out but it still dosen't come off. Going to need to use this stock cat soon..
  15. Everything Else
    images removed, sold for $200.
  16. Problems & Solutions RSX
    so im in the middle of the process of installing has port 70a billet motor mounts, these are used, i was able to get the passenger side motor mount installed fine and then i began on the rear motor mount. as i was installing them i noticed that the thread on the motor mount closes to the engine...
  17. Problems & Solutions RSX
    Stripped my caliper bolt, it's completely rounded at this point. Any IDEa of what to do beside drill it off?
  18. Suspension, Chassis & Brakes
    So, to tighten the struts on Raceland coils, you have to put an allen key on the strut bolt thing in the top hat and then tighten them with a wrench. Problem: my allen key hole is stripped. Would I be safe if I were to grab the strut at the very top of it with a wrench and then tighten it down...
  19. Problems & Solutions EP3
    well last year, i had a shop replace my front motor mount. i found out they stripped 2 of the 3 screw bolts and only installed 2 bolts anyhow I guess they stripped holes because the bolt won't stay in and the other won't tightening (screw it just keeps spinning). there was shaved aluminum on...
  20. Problems & Solutions RSX
    I was replacing my knock sensor and got the old one cross threaded on the way out. Now the new one will only go finger tight, if I try to torque it down it just spins. Is there any way to fix this? Will loctite work? Sent from AutoGuide.com Free App
1-20 of 111 Results
Top