Acura RSX, ILX and Honda EP3 Forum banner
throttle
1-20 of 500 Results
Advanced
  1. General RSX Discussion
    Ive searched around a little bit on here, but nobody with my exact symptoms. I have a clunking noise in the front right, the only time that i really can make the car do the noise is when i turn left with some speed and give gas at the same time. I have just replaced my strut mounts and have...
  2. Forced Induction & Nitrous RSX
    S90 74mm throttle body. $200/shipped
  3. Bolt-On Basics: RSX Type-S
    I'm new to after market part but not new to fixing my own car and I went to school for it too. So I need help with my 2004 RSX Type-S skunk2 pro throttle body. My set up is Borla cat-back exhaust, skunk 2 pro manifold, PLM Headers and skunk 2 Pro Throttle body. When I installed it, it started...
  4. Problems & Solutions RSX
    Hey! I have a completely stock 05 rsx type s, i bought and skunk2 intake,a k-tuned throttle body(without deleting sensor) and a k tuned fuel rail, whene ever i installed all the stuff the idle go low(like 500rpm) and have a misfire in all cylinders, i wanna know if i need a programmable ecu to...
  5. Problems & Solutions RSX
    Does anyone know where i can find a throttle wire that fits my 2003 Type S on backorder from dealer.. Is there any of the Honda with the same wire fitment?
  6. Bolt-On Basics: RSX Type-S
    What would be the best size intake manifold and throttle body for 02 type s
  7. Engine & Transmission RSX
    sold please close
  8. The DIY Garage RSX
    So I’ve been wanting to clean up the bay of my 04 Type S but I’m having trouble disconnecting the cables from the throttle body. I can’t seem to get enough leverage to undo the pins holding them in. If anyone has any photos or can tell me step by step as to how to disconnect them please let me...
  9. Problems & Solutions RSX
    whenever I’m pressing the gas it sort of hickups/lags in the lower gears, the code reader told me it was a tps issue and the dealership told me it was the throttle body. Obvisoyly i replaced the tps sensor and currently have it at .52 volts. I made the mistake of purchasing a throttle body...
  10. Part Outs RSX
    Looking for a HR TB. Anyone willing to ship let me know. Or can drive between Sacramento to LA section (California).
  11. Engine & Transmission RSX
    Willing to buy k20z1 throttle body with all sensors, and has no problems. TIA
  12. Part Outs RSX
    Willing to buy k20z1 throttle body with all sensors, has no problems. TIA
  13. Problems & Solutions RSX
    When I hook up my obd2 scanner and go to live feed, I put my foot all the way to the floor and can only reach 90.1% throttle, what can I do to get it to 100% is it mechanical? Or is it electrical? (2002 base auto)
  14. Problems & Solutions RSX
    Ok so this is driving me crazy and I need everyone’s help. My setup is Rbc manifold and s90 throttle body When my car is idling when I try and give it gas it’s difficult and takes more effort than the stock throttle body making it difficult to drive. I’ve ruled out the cable and pedal because...
  15. Engine & Transmission RSX
    selling RBC manifold that was recently sent off to be polished/cleaned with 80mm ktunned vband throttle body never used. Can send pics through phone 919-717-2635
  16. Part Outs RSX
    looking to buy a oem k20z1 throttle body with all sensors attached
  17. Bolt-On Basics: RSX Type-S
    Hey guys, I installed my new throttle body and my gas pedal gets stuck when tap it and it really gets stuck when I try and move in first gear, anyone know what I can do so the pedal moves more smoothly? (it doesn't get stuck after I press, it gets stuck before I push it)
  18. Problems & Solutions RSX
    I was in the process of changing the starter in my girlfriends 2002 Acura RSX (base model). I thought I had everything off the intake manifold, but the TPS Sensor was still plugged in. I ended up ripping the wires out of the plug trying to take the manifold off. Does anyone have any idea what...
  19. Turbo RSX
    Just looking for some insight on the Ktuned throttle cable for turbo applications. They offer three different lengths just want to know if anyone has had any experience with them and if so which size seems to work/look the best.
  20. Problems & Solutions RSX
    I had my car aligned this weekend and the guy doing my alignment said that he ran out of threads to adjust my toe while leaving my front camber at -2ish and had to bring it down to almost zero camber just to set toe withing spec. My question on this topic is do i need a shorter tie rod or...
1-20 of 500 Results
Top