my check engine light was on. it was the 02 sensor code. while driving it would loose power in neutral and shut off. while going up a slope i was doing some high revs trying to prevent the car from shutting down. heard a loud knock in the engine then the car shut down. took off the engine head...
I’ve been searching and there is little information about failures or success with different valves. I was reading that ferrea 6000 are good but they’re not designed to run with a turbo. I was thinking about ferrea comp plus but I wanted to find out if anyone has been running the 6000 or any...
k20a2! threw a rod in block only valves in cylinder one are a little beat up. can be machined. no cracks anywhere. everything has 35k miles anything you see in pictures is for sale. would like to sell head as a whole.
-12 good valves.
all valve springs
retainers
3 pistons and rods
cams...
Story time: I bought a type-s from a friend who got the P0341 code, brought it home, ordered an OE tensioner, did the timing and a compression test, determined that there are bent valves on cylinder 3 and 4. Does anybody have a good used head so I can do a direct swap? Or does anybody have any...
The head is in immaculate condition
Had 20k before sending to get ported
Only missing spring and retainers and you're ready to make up to 290 on a k20 or 300+ with a k20
For the people that know k's 163 race port is as big as it gets
No other head flows better than this
Any 163 race port head...
posted this in car care thread, but that might of been wrong area lol anyways im hoping I will get more replys here.
Im sure some will ask how the F this happened lol. During a skunk2 tb install, the s2 tb doesn't have a water port like the oem tb, anyways I had flipped the iacv for...
i have a stock 06-08 k24a2 short block that i will be mating with a 02-04 k20a2 cylinder head.
i will soon be taking the head to a machine shop once i figure out what size valves i should get.
i wanted to know how big i should/could go without hitting 12.5:1 pistons using stage 4 cams.
im...
As the title says i have 4 brand spanking new tire valves. They came in with my rpf1 wheels but decided to go with regular valves. They are blue. They're still in packaging. Took one out to take a picture of it. Its best offer takes them. Im willing to ship within the 48 states. Buyer pays...
Hey guys. another noob question but i just wanted to make sure if i needed to do anything in a particular order before spending $2,000 on my car.
So i did a compression check and a leakdown and found out my car has a broken valve. And while i'm getting my valves fixed i was going to put my...
got what i need. thanks guys!
oem k20 a2/z1/z3 valves needed.
must be in working condition. need valves for both sides.
PM or email me
[email protected]
I bought a rsx s that has a head with the valves oversized 1mm, and had sk2 stg2 cams in it but I'm attempting to return it to stock (the most I can) because I do not have kpro for it. I'm getting stock A2 cams to put back in it. But this leaves the...
Sold!!!
I have a new set never used of supertech 92lbs dual springs with flat face valves. Kit comes with spring seats, dual springs rated at 92lbs and retainers and keepers.
450 shipped anywhere in the US
I've been through a few race headers, now I have a DCRH and I can hear what I believe is exhaust valve noise resonating through the header, usually this doesn't bother me but it seems a little louder now, especcially around 3k rpm, then it becomes inaudible after that. My PLM header did the...
So, would type r cams, valvesprings, retainers, valves, and hondata itr.reflash be worth the money or no?
heard mixed opinions on type r cams, but I found a deal for 350 for the cams and valvetrain. right now I'm running a rh/cai/ex and the car is my dd
I recently finished rebuilding my engine with new pistons, rings, and bearings. I'm curious if it's possible to tell from this video that I need to adjust the valves again or if I'm just being paranoid maybe? I'm about 258~ miles into break-in using Valvoline NextGen (recycled oil in the green...
i leaning towards dished valves cause i want a lower compression but just thought i'd get some advice before i buy them. Thinking of getting the skunt 2 valves
We are pleased to offer our Ultra Series valves as our premium valve option.
They are manufactured from HNV3 Martensitic Steel (Intake) and EV8 Austenitic Steel (Exhaust).
Some of the key points of mention:
One-Piece Forging,
Chromium Nitride Coating,
Optimum Sealing, Stability and Airflow...