Search Results for ‘wear’

Just replaced all 4 rotors and pads, the rear passenger wears unevenly, pad only touched outside half of rotor and not inside, is my caliper bad...? The wear on the other 3 is f

Hey people...first off thanks for reading. Pretty straightforward symptoms, my front right and back left wheels are doing almost all of my braking. They went down to the steel while the other two wheels still had 3/8” of pad on them. Also, i couldn’t get the calipers on those two wheels to go...

TL;DR? Skip straight to the bolded questions and see if you can answer at least 1 of them... So, I've finally cracked open my clutch and have ended up with way more questions than I originally had. (Here's a link to the original thread for anyone that cares:)...

I got an alignment last year, they didn't do a very good job. I redid it myself about 6 months later to make it closer to straight. I first did the toe. It was toed out too far, so I brought it in and tightened it all up. Then I had to adjust camber on the front passenger a little out since...

I have maybe 13k on this CM fx400 and its pretty much gone. I did a 1000 mile breakin on it. Never hard launched on it. Installed it with a new light weight flywheel. I shimed the piviot ball for the release fork to correct the clutch geometry. It seems like it shouldnt be ate up this bad.

I recently switched tires, installed my winters and I noticed one of my summer tire is bald on the inside. It's the one on the rear right side of the car. Got an alignment check, toe is within spec, camber is at -3.2 deg both sides on the rear. I got an alignment with the winter tires on last...

Hi All, I'm new on the Acura RSX message boards. I own a 2006 Type-S and have had it for 6 years. It has been very good to me. But right now, I'm having the first issue I have not been able to solve. Two weeks ago, I started noticing what sounded like a metal on metal grinding. I know the...

Some background information: 2004 Type S Problem used to be bad inside tire wear on the rear due to too much rear camber ( car is lowered on unknown brand of springs) Alignment was done a few months ago and the control arms were apparently slotted by the alignment shop to get the rear camber...

Hello, my 2002 rsx type s has a nasty clunking when making a hard left turn, and the rear passenger side tire tread wears out at a much higher rate than the other 3, a used tire wears in about a month to bald. Any ideas what this could be?

Ok so I recently picked up an 03 RSX base 5spd, all stock, was used as a commuter car for gas mileage. I knew it had been setting for a while because the previous owner had bought a new car and didn't need it so i knew it was going to need brakes and it shutters and full breaking so I just...

So im getting inner tire wear on all my tires, wondering what would fix the problem? I have a camber kit installed and im only lowered 1.5 all around.. Any suggestions?? Car has 104K miles. 02 RSX-S

I'm experiencing uneven tread wear on all 4 tires. The inner and outer sides of the tire seem to be wearing a lot faster than the middle. I am running on a 05-06 type s Rims and stock suspension. Tires are Michelin Pilot Sport A/S Plus. Tires have been used approximately 20,000 miles. Anyone...

I recently installed a Competition Clutch Stage IV clutch with a Fidanza aluminum flywheel about 800 miles ago. I used wheel bearing grease on the clutch release arm pivot points during assembly. They worked great up until a week ago, when I found that the clutch would not disengage unless the...

Happy Labor Day. Anyways, inquiring about steering wheel wear. Had my '06 most of its good life. Bought at 18k back in '08 and 108k now in '13. Noticed wear just out of warranty, and see it get worse at an increased rate. Is this an 05-06 thing or all RSX's? I'm smart enough to know that your...

Hey everyone, I am in the process of installing Kelford stage 1 cams in my 06 RSX-s. I see visible wear on the cam caps. Its mainly on the intake cam side. Can i replace only the caps or should i replace the entire rocker assembly? I looked on http://www.acuraoemparts.com/ and the cam caps...

I just changed my brakes and rotated my tires and the ones that were on the rear had a lot of wear in the inside of them. Does that mean that I need an alignment?

hey i found this on the web and was thinking about putting it on the hat with the i heart ep3 on the back or the shape of our cars with ep3 in the middle. Good look or Bad? If so i was thinking maybe i would make them and give them and sell them or give them out to the ep3 owners as a prize...