wiring

Hey all, I recently purchased the Remarkable Power Fog Lights, and new being a newbie at electronic work installed it to the best of my ability. Alas, my amateur status meant not only did the fog lights not work in the end, the backlights for my gauge cluster, AC Control, and shifting lights (my...

On the base rsx the throttle position sensor is on the opposite side of the type s. U need to depin and switch over the corner wires. The middle stays the same. Would bog out under wot. Check tos calibration to be sure u got it right

I was trying to change my lights recently and I came across a problem where the low beams are cut off( previous owner modified them pretty bad). I bought the driver side headlight harness and it came with all the connectors. What I’m wondering if it’s possible to use the high beam connector on...

My headlight bulbs have wiring like this: Any suggestions on the best way to connect that wiring to the 3 prong female end on the wiring harness? Currently, I just have the ends shoved in to the appropriate power and ground spots on the female end, which works in terms of powering the bulbs...

i need to know what are the wires for in the 4-pin brake pedal switch. any help is appreciated.

Hello, I wonder if anyone could offer me some advice. I am working on replacing my starter and in the process I pulled too hard on this cable (see the pictures). I missed that it had a plastic tab to disconnect it and instead pulled it and it popped apart as you can see. The part still attached...

Audio gurus, I need help! Trying to install a backup camera. The Audiovox camera I bought is set up with the camera having a section of wiring that includes two wires to tap in to the reverse bulb in the taillight and then terminating in a yellow RCA female (pic 1). I'm good with what to do...

Okay so I’m not the first owner of my rsx and I’ve noticed a few weird things with electrical So my RSX’s cooling fans, and my interior heat/blowers don’t come on until I flip the switch on my steering colum for “daytime running lights” or turn my lights on. For example if I want my cooling fans...

I am building a tube chassis car using a K20A2. I want to install a "idiot" light for the charging system. I need to know what color wire I can tap into at the alternator to make this work. After some research I think the black with yellow is the wire , just want to be sure

Hello everyone. I'm an old member who hasn't been around for a few years. :wavey: First off, I DID search and found threads, but unfortunately the pictures are all non-functional at this point. For anyone that's running a backup camera attached to a head unit, any tips for running the wire? Am...

Hi guys, I need some help with my fog lights wiring with the 2003 Acura RSX Premium (Canadian) version. I bought the kit off of eBay, and here is the link...

Hi all, Today I was installing these headlights: https://www.amazon.com/gp/product/B0751WBD9F/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 I installed my left headlight assembly and wired it up, worked as expected. ( I quick connected the black and white LED wires to the female connect, car...

Can anyone upload a picture of the connector leading from the primary 02 sensor to where they clip. Need help figuring out what wires go into the connector and where.:hb:

hi I'm a new member but ive been browsing forums for a day or two just to see if i could figure out my problem. First, I have a engine light already on. Previous owner said they un hooked the secondary 02 sensor for "i wanted to blahblah" reasons. Hence the engine light.( come to find out he...

sold.

Pulled the engine last year, and now reinstalling it, but can't figure out what these are for? I removed the AC a few years back and didn't remove the connectors, but does the AC take these 4 plugs? I have the fan plug, drier plug, and 1 compressor plug pulled to the side not included in this...

Hi guys, Going to send my PND ECU for KPro V4 next week. Just today the dealer told me that the digital/analogue input and output wiring will be hard wired to ECU connector. Won't that will delete some of the factory functionality of the wiring as the way they connect those additional 20...

I am looking to run a water/methanol setup and wish to run the activation through Ktuner like many have done with Kpro using the E21 input and E22 output (Nitrous tab). I can not find a schematic what wires are used for the 6 programmable outputs that are available. Any input would be greatly...

I have an SRS code for the front passenger impact sensor and there is a connector that is undone somewhere between the connector behind the glovebox and the connector going into the SRS computer. Anyone know where the connectors between those 2 points are?

hey guys I was wondering if anyone knows if there is a difference between a 2002 base rsx (Canadian) and a 2002 type s also Canadian instrument/dash wiring harness? My harness is screwed and in search of a new one but all I can find is type s ones. any help would be greatly appreciated!