wrong

Looked inside and it looked like this. What’s wrong guys. Someone help Sent from my iPhone using Tapatalk

When I put the car back on the ground the sway bar is resting on the control arm and it is actually fuqn up the control arm... did I put it in upside down or something Sent from my iPhone using Tapatalk

I just bought a base rsx few weeks ago. Among the problems is it has a mswa transmission in it. I'm having problems finding any information on this transmission other than it's a 4speed. Does anyone have any info on these transmissions?

I ordered a new Denso Direct-Fit O2 sensor to fix my p1166-67 codes, so I was expecting a primary. After the impulse buy at a $50 discount(Still overpayed looking back) and screwing in the new sensor, I notice the connectors are the same! Looking back I see this was a huge NOOB mistake! Can I...

Is everyone tapping or welding there turbo drain in the wrong spot? I took an extra PRB RSX oil pan and filled it with 6 quarts of water. My RSX takes 6 quarts of oil. It was nearly filled to the top. The K motors have a slight tilt to them. During a 1/4 mile run, and the fact that the RSX does...

Please delete

Seller refunded money please closed.

Okay, 2002 RSX type S with Greddy turbo kit. I bought it for my gf. She's never driven standard before and this is a hard car to learn on because it has a racing clutch on it. While teaching her standard she often stalls and the car bucks a lot. -So much so that the exhaust hangers actually...

Team, just finished fitting my BuddyClub coilovers to my RSX and have come across a problem I've never encountered before when fitting suspension Basically the O/S went on fine with no issues but when I fitted the N/S, the toe angle was WAY out...see pictures below: Good side: Bad side...

I hate starting a new thread but i have a little issue ... I had my car since 2008 and didnt realize that previous owner or dealership had replaced this sensor and apparently messed up the wiring inside blue plug ,plastic inside looks broken and wires are moving around and if i wiggle those...

I got these ASA EM9 wheels 16x7 for my 03 EP3(4x100). When i tried to mount them the other day i couldnt quite put the lugs on i got one on but i had to really struggle to get it on there:mad:. The off set is ET35 but i have no clue what that is i just want the wheels on my damn car. the tire...

Waiting for a response from Rock Auto, but figured I would post here to get any possible input. This is the drivers side. The old axle came out very easily. I am having trouble getting the new one to "seat" Different enough design to cause this ? I usually don't have trouble seating these...

For the past two weeks, I noticed a sluggish performance of my RSX. Every time I accelerate, I hear this "ta ta ta" sound coming from the engine. When I sit engine idel with heat on and circulation off, I can smell gas fume coming inside. The engine sound louder than usual. Can someone tell...

Hey everyone, I started having an issue with my 2002 RSX type s. I bought it used and it was working fine before yesterday. Now it turns on stays on for 5 seconds and turns off. I can keep it running if I rev it past idle. The next issue is that if it tried to die while i was revving and i kept...

I took my front calipers off to paint them, I put them back on filled up the fluids but the rubber boot in the brake fluid reservoir basically won't fit on the cap or in the reservoir so I stuffed it in there and now I have no brake pressure !!! Help !!!! :laughat::firemad:mad:

so where to begin... I had my tranny rebuilt about 2 months ago and there were a couple other things on my 02 rsx -s that I wanted to replace, but today I went to get an alignment and got an estimate $741. Well my car couldn't even be aligned because my LCA was bent with a missing end link. also...

I actually posted a thread but didnt get to many responses....but here i am again. My sub frame on 02 type s is touching with the oil pan. Was wondering if it would be a problem with the sub frame or the motor mounts that don't work. need help before i buy something that i don't need.

Yes i know i start a lot of my threads with "gone wrong" lol. I'm a horible mechanic i need to start paying people when i need things done. So i decided to clean my TB for no apparent reason, just felt like it. Also. attempted to clean IACV but it was bleeping seized in place. no way it was...

Well long story short I FORCED some lugs that were 12x1.25 on my studs which are 12x1.50.. a now very unreliable source said my stud size was x1.25 when in reality theyre 1.5 I got 17 out of 20 lugs on before I realized I screwed up, the lugs are on tight so I think I can drive around for a few...

Hey guys, Just bought a new set of rims today from my buddy, anyway I was real excited to put them on, first three wheels I put them on, didn't notice anything out of the ordinary, then on the last one I guess I didn't bolt it on tight enough and it shook when I drove so when I got back home i...