Acura RSX, ILX and Honda EP3 Forum banner
1 - 20 of 21 Posts

·
Registered
Joined
·
258 Posts
Discussion Starter · #1 ·
I noticed on here, alot of people keep asking where to find the JDM Sidemarker Template, Well i have the Sidemarker Template in a Jpeg format. Hope this helps :thumbsup:

If this has already been covered im sorry for reposting, But maybe it will make things easier on how to find it.

All you have to do is save this file, Then when rdy to print, Make sure you print this "Print to fit screen" and the measurements should be exact, (At least they were on mine :))

 

·
Registered
Joined
·
258 Posts
Discussion Starter · #3 ·
those must be some tiny side markers. good effort though. :thumbsup:

Here is the template by the way.
Reason i said when you print you "Print to fit screen" and they come out to be the exact measurements.

Did mine that way, And i installed mine without a problem.
 

·
Special Olympics Winner
Joined
·
3,031 Posts
would a dealership install these im so scared to cut the fenders
 

·
wtfhax0r
Joined
·
7,507 Posts
would a dealership install these im so scared to cut the fenders
dont be afraid to do it, just use a dremel and cut VERY slowly, starting smaller than you need to then work your way to a bigger hole until it fits snug. make sure you put painters tape around where youre cutting and get touchup paint for the exposed metal afterwards so it doesnt rust.
 

·
2.slow
Joined
·
915 Posts
dont be afraid to do it, just use a dremel and cut VERY slowly, starting smaller than you need to then work your way to a bigger hole until it fits snug. make sure you put painters tape around where youre cutting and get touchup paint for the exposed metal afterwards so it doesnt rust.
I dont recommend starting out smaller b/c i used this template and cut right on my traced lines and it was still a little small..Had to trim a little more. if you start out smaller then the template then you will be there awhile trimming. the longer you cut on your car the higher the chance of skining up your paint..Oh and make sure you purchase the re-inforced cutting wheels they come in a five pack at walmart and are like 5 dollars, i only used 2 cutn wheels when i did mine. i will try to post some pictures soon...
 

·
_________________________
Joined
·
3,482 Posts
I dont recommend starting out smaller b/c i used this template and cut right on my traced lines and it was still a little small..Had to trim a little more. if you start out smaller then the template then you will be there awhile trimming. the longer you cut on your car the higher the chance of skining up your paint..Oh and make sure you purchase the re-inforced cutting wheels they come in a five pack at walmart and are like 5 dollars, i only used 2 cutn wheels when i did mine. i will try to post some pictures soon...
x2 my 1st time I went with cheap ones at target and went through like 15 of them :jigglemad brought the re-inforced ones and broke only 1.
 

·
Registered
Joined
·
258 Posts
Discussion Starter · #14 ·
nice..the template did not come with my sidemarkers
If the template didnt come with the markers when ordered, try contacting the company that you bought the sidemarkers from, and they should be able to e-mail you a template. I bought mine from wotm.com and they sent the template in a PDF file through e-mail.
 

·
Manny Pacquiao FTW!
Joined
·
11,841 Posts
If the template didnt come with the markers when ordered, try contacting the company that you bought the sidemarkers from, and they should be able to e-mail you a template. I bought mine from wotm.com and they sent the template in a PDF file through e-mail.
thanks man, i will just email kamispeed
 
1 - 20 of 21 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top